Partial wavelength for electromagnetic energy

Assignment Help Civil Engineering
Reference no: EM1383486

What is the length of the partial wavelength for electromagnetic energy with a frequency of 15 MHz and a phase shift of 263 degrees (in meters)?

Reference no: EM1383486

Questions Cloud

Estimating the volume of soil in cubic meters : The void ratio of soil in the borrow pit is 1.12. Estimate the volume of soil (cubic meters) that must be excavated from the borrow pit.
Long cantilever beam of elastic modulus : A 45 kg machine is placed at the end of a 1.6 m long cantilever beam of elastic modulus 200 x 109 N/m and cross-sectional moment of inertia 1.6 x 10-5 m4.
Finding the gallons of mercury : How many gallons of mercury (sg=13.54) would weight the same as 5 gallons of castor oil which has a specific weight of 56.69 pcf?
Time inventory system for a product : How appropriate might a just in time inventory system be for a product such as roller skates?
Partial wavelength for electromagnetic energy : What is the length of the partial wavelength for electromagnetic energy with a frequency of 15 MHz and a phase shift of 263 degrees (in meters)?
Constant head permeability test : A constant head permeability test was conducted on a clean sand sample. The diameter and length of the test specimen were 10 cm and 12 cm respectively.
Volume of soil-excavated from the borrow pit : The volume of fill required is 2500 cubic meters. Find the volume of soil that must be excavated from the borrow pit to furnish the required volume of fill. (in cubic meters).
Bernoulli equation-measure the flow rate through the meter : The meter inlet and throat are connected by the two legs of a mercury manometer. Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.
Average shearing stress : Two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Problem on coefficient of rolling resistance

What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitting it? Assume coefficient of rolling resistance of 0.013.

  Thermo-gravimetry of calcium oxalate

Evaluate the percent mass loss for each of the three thermal events indicated on the attached TGA trace

  Determine the stress state at points a & b

CE 3303 – Solids – MWF – Spring 2014 - Homework Set 23, – The pipe shaft of the auger, rotating at a constant angular velocity, is subject to the axial force and torque shown. Determine the stress state at points A & B and show on a stress element.

  Total vehicle delay in the cycle with queueing diagram

If the queue clears exactly at the end of the effective green D/D/1 queuing applies, determine the total vehicle delay in the cycle (in veh-sec) .

  Engineering ethics and concept and cases

what is the engineering ethics case related to civil engineering with reference and discuss all the engineering ethics issues which covered the "Engineering etics concepte and cases?

  Base of each standpipe

Determine: a) the height of the water, with respect to the base of each standpipe, and b) the effective stress at the depth of each standpipe, at the following times:

  Radioactive waste from a clinical laboratory

A radioactive waste from a clinical laboratory contains 0.2 μCi (microcuries) of calcium-45 (45Ca) per liter. The half-life of 45Ca is 152 days.

  Uniform deterministic arrival rate

Processing begins when the lane reaches capacity, what is the uniform deterministic arrival rate if the vehicle queue is cleared in 35 minutes after vehicles begin to arrive (in veh/min.)?

  Parallel tangents of a reversed curve

The perpendicular distance between two parallel tangents of a reversed curve is 20m. The azimuth of the back tangents of the curve is 270 00 and the azimuth of the common tangent is 310.

  Crystalline or atomic structure

Describe the crystalline or atomic structure of the following minerals: 1) Brucite 2) Gibbsite 3) Bentonite 4) Illite

  Calculate the total drilling cost

Calculate average figures for tonnes/round and powder factors in kg/tonne and Determine the drill metres required to achieve a production rate from grade control blasting.

  Shear tension and bending of the fixed i-beam

To satisfy desige limitation it is necessary to determine the effect of the 2- kN tension in the cable on the shear tension and bending of the fixed I-beam.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd