One would like to find preheat 2 tons h of a solution with

Assignment Help Mechanical Engineering
Reference no: EM13631036

One would like to find preheat 2 tons / h of a solution with a specific heat capacity of 3.35 kJ / kg * K from 15 C to 70 C using hot water. The water temperature drops from 95 C to 35 C. Heat thru coefficient U = 700 W/m2 * K. Calculate the heat surface and consider the heat exchanger should be with the flow or countercurrent.

Reference no: EM13631036

Questions Cloud

Heat loss of 03 kw occurs from the compressor to the : air flows steadily through a compressor at the rate of 1.57 kgmin. the compressor requires 5 kw power input to compress
How large a current in the equatorial plane would be : suppose that the magnetic field of the earth were due to a single current moving in a circle of radius 2910 km through
A car radiator has an effective heat transfer area of 15 m2 : a car radiator has an effective heat transfer area of ??15 m2. cooling water temperature is 85 c in and the 60 c out of
Where the x- and y-coordinates are in m and the magnitude : a steady incompressible two-dimensional velocity field is given byvuv12.5xyi-.5-1.5x-2.5yjwhere the x- and
One would like to find preheat 2 tons h of a solution with : one would like to find preheat 2 tons h of a solution with a specific heat capacity of 3.35 kj kg k from 15 c to 70
A 25 t magnetic field passes through a circular ring of : a 2.5 t magnetic field passes through a circular ring of diameter 3.0 cm at an angle of 30o with the normal. find the
A well-insulated rigid tank contains 5 kg of a saturated : a well-insulated rigid tank contains 5 kg of a saturated liquid-vapour mixture of water at
The device is not insulated and operates in an environment : a refrigeration engineer has designed a steady-flow no work interaction device that separates a continuous flow of 100
A block is made of an unknown material when placed in : a block is made of an unknown material. when placed in water the block floats and 4 m3 of the block is observed to be

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The length of pipe is 30 m and contains two elbows with

a solution of ethanol is pumped to a vessel 25 m above a reference level through a 25 mm inside diameter steel pipe at

  Calculate the average square distance

Calculate the average square distance between the particles and plot its ratio to the time step . This is the diffusion/dispersion coefficient.

  Air at 01 kgs is to be cooled from 140 c to 40 c in a heat

air at 0.1 kgs is to be cooled from 140 c to 40 c in a heat exchanger. the coolant water is at 20c constant throughout

  Determine a velocity using bernoullis equation

If I take measurements using a Pitot Tube and get results for pressures Horizontal In, Horizontal Out, Vertical In, and Vertical Out all in inches of mercury. How do I take these pressures and determine a Velocity using Bernoullis equation?

  Determine the linear coefficients of expansion

What was the percentage error found between experimental and accepted values and what caused any errors, and how could they be minimised?

  Knowing that the fairway slopes downward at an average

a golfer hits a golf ball with an initial velocity of 160 fts at an angle of 25deg with the horizontal. knowing that

  For the compressor the isentropic efficiency is 92 and for

air enters the compressor of a regenerative air-standard brayton cycle with a volumetric flow rate of 60 m3s at 0.8 bar

  Find the enthalpies and entropies at each point around a

find the enthalpies and entropies at each point around a simple rankine cycle. assume that prior to entering the pump

  Determine position x for the slider

Assuming a small oscillation about the horizontal equilibrium position, determine position X for the slider such that the friction period is 1 second.

  Air enters a steady-flow compressor with a specific

air enters a steady-flow compressor with a specific enthalpy of 293.4 kjkg and a velocity of 60ms and leaves with a

  What is the static sensitivity estimate the total

a nominally linear electrical output force measuring device has the manufacturer specifications listed below. the

  An adiabatic capillary tube is used in some refrigeration

an adiabatic capillary tube is used in some refrigeration systems to drop the pressure of the refrigerant from the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd