One-tenth kg of a gas in a piston-cylinder assembly

Assignment Help Mechanical Engineering
Reference no: EM13631464

One-tenth kg of a gas in a piston-cylinder assembly undergoes a Carnot power cycle for which the isothermal expansion occurs at 800K. The change in specific entropy of the gas during the isothermal compression which occurs at 400K, is -25Kj/Kg.K. Determine (a) the net work developed per cycle, in kJ, and (b) the thermal efficiency.

Reference no: EM13631464

Questions Cloud

The pressure drop needed to force water through a : the pressure drop needed to force water through a 1-in.-diameter pipe the pipe is on a 20 degree hill is 0.76 psi for
Graph the sample means with the values of on the horizontal : the following information gives the number of days absent from work for a population of 5 workers at a small factory.
Assuming the specific heat of the body is the same as water : assuming the specific heat of the body is the same as water calculate the temperature rise due to a total body dose of
The reactor was empyu at the start of the experiment if : a solution containing bacteria at a concetration of .001gl was fed to a semibatch reactor. the nutrient was in excess.
One-tenth kg of a gas in a piston-cylinder assembly : one-tenth kg of a gas in a piston-cylinder assembly undergoes a carnot power cycle for which the isothermal expansion
The brothers depart at the same time while salviatis : the relativity twins simplicio and salviati are taking separate spaceships to another planet which we have measured to
Determine the irreversibility in kjmin for 1 the heat pump : a heat pump units operates between two heat reservoirs with temperatures of 270 and 330 k. the heat pump its self has a
The condenser pressure is 50kpa and the steam exits the : the steam turbine power plant uses water as the working fluid and will be modeled as a simple ideal rankine cycle. the
1-2 an actual refrigerator absorbs 500 kj of heat from a : 1-2 an actual refrigerator absorbs 500 kj of heat from a sink at 250 k and reject 660 kj of heat to environment at 300

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The diameter of the ball is 2001 cm and the inner diameter

an aluminum ball does not fit through a brass ring at 20oc. the diameter of the ball is 2.001 cm and the inner diameter

  Bubble dynamics underneath a downward facing anode

Bubble dynamics underneath a downward facing anode in Hall-Heroult cell. Experimental using Hall-heroult process.Analysis by using High Speed Camera and ANSYS Model.

  A single-pane glass window is used in a heated dwelling

a single-pane glass window is used in a heated dwelling. outside the dwelling the ambient temperature is 0degc while

  Design of absorption column and the cooler process design

design of absorption column and the cooler process design of other units should be completed along with pipe sizes. the

  The nominal composition by weight of this material is as

stainless steel type 304 having a density 7.86 gmcm3 has been used in some reactors. the nominal composition by weight

  If the air undergoes an adiabatic expansion process through

air at 800 kpa and 400oc enters a steady-flow nozzle with a low velocity and leaves at 100 kpa. if the air undergoes an

  Determine the maximum flexural strength

Immediately before failure, the testing machine records a force (F) of 50N, and a deformation (δ) of 2mm. We need to determine the maximum flexural strength (σ)

  Kinetic and potential energy changes from inlet to exit can

at steady state a well-insulated compressor takes in air at 60 degrees f 14.2 lbfin2 with a volumetric flow rate of

  Also venous blood enters at 0 mm hg and leaves at 15 mm hg

imagine that the heart acts as a pump. blood enters the heart from the lungs at 6mm hg and leaves to the rest of the

  Explain horsepower and efficiency of three-phase motor

Horsepower and efficiency of three-phase motor, If a fully loaded 440V, three-phase motor draws 12.4 A at 86% power factor (pf). It's speed is 1730 rpm and its torque output to a mechanical load is 29.1 lb-ft x 1.356 = 39.5 Nm.

  An extruded beam has the cross section shown and a uniform

an extruded beam has the cross section shown and a uniform wall thikness of 3mm. for a vertical shear of 1.2 kips

  A steel pipe of 100-mm diameter is to support the loading

a steel pipe of 100-mm diameter is to support the loading shown. knowing that the stock of pipes available has

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd