On the right side of the truss there is 6000 n worth of

Assignment Help Mechanical Engineering
Reference no: EM13621508

There is truss that is an upsidown triangle, with two twenty degree angles and is hooked up to four members with pin joints (On the right side of the upsidown triangle truss the fourth member goes straight up from a pin joint on the floor to the right side of the triangle). On the left end there is 4,000 N worth of force pushing down. Half a meter along the x direction the top of the upsidown triangle is hooked up to a pin joint to the floor, the entire truss in 1 meter. On the right side of the truss there is 6,000 N worth of force going in the possitive x direction.

1) Calculate the external loads on each member using the general mothod for sturctures.

a) Neglect the weight of the members.

b) assume each member has a mass of 100 kg/m.

Reference no: EM13621508

Questions Cloud

Suggest how a financial analyst would determine if the : 1. justify the importance of investment diversification. explain your rationale.2. suggest how a financial analyst
A survey of 1305 people who took trips revealed that 96 of : 1. a noted psychic was tested for esp. the psychic was presented with 200 cards face down and was asked to determine if
The index of refraction for violet light in silica flint : the index of refraction for violet light in silica flint glass is 1.66 and that for red light is 1.62. what is the
The muse co just issued a dividend of 275 per share on its : the muse co. just issued a dividend of 2.75 per share on its common stock. the company is expected to maintain a
On the right side of the truss there is 6000 n worth of : there is truss that is an upsidown triangle with two twenty degree angles and is hooked up to four members with pin
Famas llamas has a weighted average cost of capital of 105 : famas llamas has a weighted average cost of capital of 10.5 percent. the companys cost of equity is 16 percent and its
Mudvayne inc is trying to determine its cost of debt the : mudvayne inc. is trying to determine its cost of debt. the firm has a debt issue outstanding with 16 years to maturity
If the rod has a mass of 123 kg and a length of 125 m and : you are at a furniture store and notice that a granfather clock has its time regulated by a physical pendulum that
A newspaper conducted a statewide survey concerning the : a newspaper conducted a statewide survey concerning the 1998 race for state senator. the newspaper took a srs of n1200

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd