User Account

All Pages

Oil a has a viscosity of 80cst at 40c and 8cst at 100c oil

Assignment Help Mechanical Engineering
Reference no: EM13625273

Two oils are tested to establish their viscosity index. Oil "A" and Oil "B" have their viscosity measured at temperatures of 40C and 100C. Oil "A" has a viscosity of 80Cst at 40C and 8Cst at 100C. Oil "B" has a viscosity of 90Cst at 40C and 15Cst at 100C. Which oil has the higher viscosity index?

Reference no: EM13625273

Questions Cloud

Diffusive jumps will be made from the body center atom : structure of body- centered cubic bcc crystal.a. the body-center atom in a conventional bcc unit cell has
If these viscosities are the safe limits for the oil : a pump fitted with 50mm bore ball bearings uses an oil whose viscosity ranges from 100cst at cold pump start-up to
The distribution of sample means will not be normal even : nurses wondered if birth weights of babies are going up. they knew that the average birth weight of a baby last year
A proton mass m 1673 x 10-27 kg is bound in a finite : a proton mass m 1.673 x 10-27 kg is bound in a finite square well of width 4fm. the depth of the well is six times the
Oil a has a viscosity of 80cst at 40c and 8cst at 100c oil : two oils are tested to establish their viscosity index. oil a and oil b have their viscosity measured at temperatures
Given the following operating conditions for a rolling : given the following operating conditions for a rolling bearing what lubricant would you select and what is the reason
Man 1 was experimenting with friction and attempting to : man 1 was experimenting with friction and attempting to pull man 2 across the surface of a floor. man 1 applies a
An electric current of 025 a flows through a 5-ohm : an electric current of 0.25 a flows through a 5-ohm electrical resistor placed in an evacuated chamber. the resistor is
Man 1 was experimenting with friction and attempting to : man 1 was experimenting with friction and attempting to pull man 2 across the surface of a floor. man 1 applies a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the minimum mass flow rate kgs of the water so

a liquid sodium flowing a 100 kgs enters a heat exchanger at 450 c and exits at 350 c. the specific heat of sodium is

  A thin circular cylindrical shell subjected to internal

a thin circular cylindrical shell subjected to internal pressure p isnbspsimultaneously compressed by an axial load p

  How far has the mass moved when its velocity is 243 ms

a hollow cylinder is made by welding two thin disks on either side of a thin ring. it is mounted on a axel and a 2 kg

  For a newtonian fluid or a power law fluid flowing through

for a newtonian fluid or a power law fluid flowing through a cylindrical tube of radius r calculate the constant k in

  Goldilocks illegally entered the house of three bears where

goldilocks illegally entered the house of three bears where she found three bowls of por-ridge a 2.0-quart bowl at

  Determine the moment about c of that force

A wooden board AB, which is used as a temporary prop to support a small roof, exerts at point A of the roof a 57-lb force directed along BA. Determine the moment about C of that force.

  Determine the control resolution for this robot

The linear joint (Type L) of a certain industrial robot is actuated by a piston mechanism. The length of the joint wehn fully retracted is 600 mm and when fully extended is 1000 mm. If the robot's controller has an eight-bit storage capacity, dete..

  An automobile traveling at 90 kmhr rounds a long sweeping

an automobile traveling at 90 kmhr rounds a long sweeping curve of radius 250m. the air conditioner is on and the

  Find the rectangular representation of v

a velocity vector v is deirectred from point A (0,10,-8) toward point B (24,-18,0), WHERE THE COORDINATES are in feet. find the rectangular representation of v, given that its magnitude is 12 ft/s

  Investigating a dynamic movement in polar coordinates

Investigating A Dynamic Movement in Polar Coordinates

  Determine the acceleration of the water particles that are

a sprinkler essentially consists of a pipe ab mounted on a hollow shaft. the water comes in the pipe at o and goes out

  What is the correct speed at which the compressor must run

a compressor is designed to run at 4000 rpm when ambient conditions are 101 kpa and 20c. on the day when the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd