Obtain a relation for the variation of pressure in the

Assignment Help Mechanical Engineering
Reference no: EM13619038

Temperature varies with altitude. The variation in the temperature can be approximated by T=T0 -beta z, where T0 is the temperature at sea level, which is 288.15 K, and beta = 0.0065 K/m. The gravitational acceleration also changes with altitude as g(z)=g0 1(1+z/6,370,320)2where g0= 9.807 m/s2 and z is the elevation from sea level in m. Obtain a relation for the variation of pressure in the troposphere (a) by ignoring and (b) by considering the variation of g with altitude. The troposphere extends to an altitude of 11 km.

Reference no: EM13619038

Questions Cloud

Calculate midlands corporate wacc be prepared to defend : 1. how are mortensens estimates of midlands cost of capital used? how if at all should these anticipated uses
A force has a strength of 87 n and makes an angle of 21 : a force has a strength of 87 n and makes an angle of 21 degrees with respect to the positive x axis in the x-y plane.
Draw a diagram of the system and state necessary : design a stationary steam power plant operating on an ideal closed loop rankine cycle that can deliver 85 mw of net
Houma bio-control has hired you as a consultant to assess : houma bio-control has hired you as a consultant to assess the economic feasibility of investing 2500000 to purchase a
Obtain a relation for the variation of pressure in the : temperature varies with altitude. the variation in the temperature can be approximated by tt0 -beta z where t0 is the
The board for colton industries is considering a proposal : the board for colton industries is considering a proposal by the ceo to sell the firms boat manufacturing division. an
Determine the volume flow rate and the density of the gas : carbon dioxide gas enters a pipe at 3 mpa and 500 k at a rate of 2 kgs. the gas is cooled at constant pressure as it
Determine a overall efficiency of the pump-motor unit and b : water is to be pumped from a dam to a storage tank 20 m above at a rate of 70 ls. the electric power needed to achieve
At year-end 2013 wallace landscapings total assets were 217 : at year-end 2013 wallace landscapings total assets were 2.17 million and its accounts payable were 560000. sales which

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assume that the internal energy and specific volume of

the pressure of 200 kgs of water is to be increased from 1 atm to 4 mpa. the water enters through a 20-cm-diameter pipe

  There are 18 turns in the primary coil and 20 turns in the

a transformer consisting of two coils wrapped around an iron core is connected to a generator and a resistor as shown

  Determine the mass moment of inertia

A flywheel can be considered as being composed of a thin disc and a rim. The rim weighs 322 lb and has diameters of 24 in. and 30 in. The disc weighs 64.4 lb. Determine the mass moment of inertia about the centroidal axis about which the flywheel ..

  Determine the angular velocity theta dot of the combined

a wad of clay mass m1 with an initial horizontal velocity v1 hits and adheres to the massless rigid bar which supports

  An exit air bulk average temperature t bo 127 0c is

air at 1.0 atmosphere pressure and 77 0c enters a 5.0 mm i.d. tube with a bulk average velocity of 2.5 ms. the velocity

  After drawing a neat and clear schematic of the geometry

a 5 ft3 tank containing steam at 14.7 psia 1 quality is fitted with a relief valve. heat is transferred to the tank

  Water is pump from a lake to a storage tank at 18m above at

water is pump from a lake to a storage tank at 18m above at a rate of 70 ls while consuming 20.4 kw of electric power.

  Compute the weight percent of niobium

Niobium forms a substitutional solid solution with vanadium. Compute the weight percent of niobium that must be added to vanadium to yield an alloy that contains 1.55 x 1022 Nb atoms per cubic centimeter. The densities of pure Nb and V are 8.57 an..

  Determine the isentropic and actual work output for the

consider an adiabatic turbine with an isentropic efficiency of 85. the inlet pressure and temperature are 3.50 mpa and

  The plant manager decided to build a model however test

axial flow coolant pump for one lop pressurized nuclear reactor has 75 m head 6m3s flow rate 1440rpm 800 mm diameter

  Find the height of center of mass

find the best fit Gaussian Curve through the data and plot the data and curve on the same graph.

  Calculate the rate of water removal from the condenser the

an air conditioner is used to cool and dehumidify air. we will ignore the temperature aspect and model the air

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd