Reference no: EM13289232
1. Convention Milling or ( Up-Milling ) can best be described as:
The Feed Direction of the table is in the “same direction”of the cutter.
The Feed Direction of the table is “opposite the direction” of the cutter
Is the preferred choice when milling
None of the above
2. The Selection of Helix Angle for (End Mills) is based on the machining task.
Aluminum can” best” be machined with a Helix Angle of?
Low Helix Angle around 12°
High Helix Angle 45°
Medium Helix Angle 30°
All of the above
3. A fellow student needs help calculating the RPM for a ½ End mill, which formula below is correct?
RPM = (3.82 X SFM) / Cutter Dia.
RPM = 3.82 X SFM X Cutter Dia.
RPM = (Cutter Dia. X SFM)/3.82
RPM = (Cutter Dia. X 3.82)/SFM
4. An End that is designed to remove large amounts of material ( quickly )
This end mill is called?
Ripping End Mill.
Roughing or (Hogging) End Mill.
Shark Cutting End Mill because it has so many teeth.
4-Flute End Mill with a slow helix angle of about 12°
5. The correct “Feed Rate” for milling is expressed in Inches per minute ( IPM )
The correct formula is? : Note the formula in the Text uses (N) instead or (T)
IPM = (FPT X T)/RPM
IPM = FPT x T x RPM
IPM = (RPM x FPT) / T
IPM = (T x RPM)/FPT
6. From question # 6 what is the correct “IPM Feed Rate” given the following info:
Rpm=1500, 4 flute end mill, FPT=.005”
IPM =30
IPM = 1.875
IPM=120
IPM = 1.33
7. As a general rule the Depth of cut ( DOC ) of and end mill should not exceed ____________of the tool diameter in steel.
.500
.375
.250
.125
8. End-mills that is capable of making their own starting hole are known as ______ end mills.
Center Cutting
Start Cutting
Rough Cutting
Cavity Cutting.
Warehouse to accommodate five-day supply of cell phones
: A factory produces 15,000 cellular phones per day. The dimensions of each cell phone are 5 x 2.5 x 2.5 inches. Management wishes to have a one-week (five-day) supply in stock. One hundred cell phones are packed in a carton, and cartons may be stacked..
|
Attributes of speaker’s voice can be positive or negative
: Think about how the attributes (pitch, volume, pace and quality, articulation) of a speaker’s voice can be positive or negative. Are either extremes of these qualities positive or negative?
|
Function of punishment-deterrence-retribution-prevention
: What should be the function of punishment: deterrence, retribution, prevention, reform? Does your answer change with varying crimes?
|
Networks use different routing protocols
: Networks use different routing protocols to select the best routing path to reach other networks. A distance-vector routing uses a set of protocols (IPX, SPX, IP, or DECnet) and a distance calculation through an outgoing network interface to select t..
|
Convention milling or up-milling can best be described
: End-mills that is capable of making their own starting hole are known as ______ end mills. Convention Milling or ( Up-Milling ) can best be described as: A fellow student needs help calculating the RPM for a ½ End mill, which formula below is correct..
|
Advantages is distribution of the burden on top executives
: One of the primary advantages is the distribution of the burden on top executives. By delegating authority to lower levels in the organization, top executives are better able to concentrate on activities that are more strategically future-oriented, ..
|
What percentage did net income increase
: Assume Main Street Store’s Net Sales in 2010 were $1,000,000 and it’s Net Income in 2010 was $17,000. Thus, between 2010 and 2011 Main Street Store’s net sales increased 20%. During the same period what percentage did net income increase?
|
Define ergogenic aid-explain how steroids are considered
: Define ergogenic aid and explain how steroids are considered part of your definition. Summarize your findings in the context of exercise science.
|
Explain how steroids differ from the human growth hormone
: Explain how steroids differ from the human growth hormone. Summarize your findings in the context of exercise science.
|