Numerically calculating radiation heat transfer coefficient

Assignment Help Mechanical Engineering
Reference no: EM13701678

Consider water again in a 1 liter bottle in the shape of a cylinder.

a. Estimate the combined thermal resistance of a 1 liter cylindrical bottle for the following situation:

The inside diameter of the bottle is equal to the inside height of the bottle

The wall thickness is 0.2 cm,

The bottle is made of aluminium,

The air is moving around the bottle at 10 m/s

Both convection and radiation occur on the outside of the bottle

b. Write the equation to assess the ratio of radiation resistance over convection resistance.

c. What is missing from numerically calculating the radiation heat transfer coefficient?

d. Is the fact that water is inside the bottle relevant, i.e. is it needed to assess the thermal resistance?

 

e. Is the fact that air is outside the bottle relevant?

Reference no: EM13701678

Questions Cloud

The heat transfer from one side of the door to the other : Consider a wooden door with a glass window. The door is 5 cm thick and 0.75 m wide by 2 m tall. The window is 0.2 m square and 1 cm thick. The air on one side of the door has a temperature of 23°C and a heat transfer coefficient of 10 W/m2-K. The air..
Additionally determine the ratio of cross-sectional areas : A solid shaft of diameter D is used to carry an applied torque T. At the time of regular maintenance, engineers decided to replace it with an alternative shaft of hollow geometry with an inner diameter din = D. Considering that the maximum shear stre..
The average temperature on each side of the door : Consider a wooden door with a glass window. The door is 5 cm thick and 0.75 m wide by 2 m tall. The window is 0.2 m square and 1 cm thick. The air on one side of the door has a temperature of 23°C and a heat transfer coefficient of 10 W/m2-K. The air..
What is tension in the swing cable developed during motion : A gantry structure, similar to a tire swing, is used to test the response of an airplane during a crash. A 8000kg plane is hoisted back until the 20m swing cable is at theta=60. Determine the speed of the plane just before crashing into the ground at..
Numerically calculating radiation heat transfer coefficient : The inside diameter of the bottle is equal to the inside height of the bottle. Write the equation to assess the ratio of radiation resistance over convection resistance. What is missing from numerically calculating the radiation heat transfer coeffic..
Liquid in a tube varies with tube diameter : The capillary rise, h, of a liquid in a tube varies with tube diameter, d, gravity, g, fluid density, p, surface tension, Y, and the contact angle, B. (a) Find the dimensionless form of this statement. (b) If h = 3 [cm] in a given experiment, what wi..
. indicate whether each member is in compression or tension : Determine the forces in members DE, and DJ, and IJ using the method of sections. Indicate whether each member is in compression or tension.
Suppose an object moves on a horizontal line : Suppose an object moves on a horizontal line. If the object starts from rest at the origin and it has an acceleration of 16t-t, Determine the total distance the object has moved when time is 2 seconds. Note the distance moved is not the position. For..
Determine total and flow energies of the steam per unit mass : Steam is leaving a pressure cooker whose operating pressure is 30 psia. It is observed that the amount of liquid in the cooker has decreased by 0.45 gal in 60 minutes after the steady operating conditions are established, and the cross-sectional area..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What volume must be provided in a methane tank to hold

what volume must be provided in a methane tank to hold 10kg of methane at 1500 kpa and 30 degrees celsius? if the

  Determine the initial discharge rate of water

The tank air pressure above the water level is 300kPa(absolute) while the atmospheric pressure is 100kPA. Neglecting frictional effects, determine the initial discharge rate of water from the tank.(Density of water=1000kg/m^3)

  Assuming the heat transfer from the back side of the plate

an array of power transistors dissipating 5 w of power each are to be cooled by mounting them on a 25cm x 25cm square

  The heat flux passing through a plane wall of a

the heat flux passing through a plane wall of a well-insulated house is q 2.5 btuhr-ft2 when the temperature of the

  Determine the yearly electrical cost to operate this motor

a 50 hp electric motor is powering a pump that operates for 8 hours a day for 360 daysyear. for an industrial

  Emissions and reflections

Use a suitable method to predict the racS,T variation along these plates when a= e= 0.1, 0.5, and 0.8 and emissions and reflections are diffuse.

  Determine the power produced and the rate of process heat

steam is generated in the boiler of a cogeneration plant at 10 mpa and 450 degrees c at a steady rate of 5 kgs. in

  If d 10 cm h6 cm and q0380 m3s what are the velocity in the

air discharges downward in a pipe and then outward between the parallel disks. assuming negligible density change in

  Compute the equations of streamlines that pass through xy

for the two-dimensional flow with velocity components u y - 2 and v 2x3i compute the equations of

  Calculate the air temperature and pressure at the

calculate the air temperature and pressure at the stagnation point right in front of a meteorite entering the

  The steam line leading to the turbine inle

The steam line leading to the turbine inle

  Determine the diameter of the standard commercial steel

a pump is located 4.5 m to one side of and 3.5 m above a reservoir. the pump is designed for a flow rate of 6 ls. for

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd