Normal capacity by using hose connected to kitchen faucet

Assignment Help Mechanical Engineering
Reference no: EM13709050

Due to drought, the water level of a 10-acre pond is five feet below normal. If you wanted to fill the pond to normal capacity by using a hose connected to your kitchen faucet, how long would it take to fill the pond? Select an appropriate unit of time to report your answer. Make sure you write your solution in detail and stepwise manner.

Reference no: EM13709050

Questions Cloud

Express the acidity of the wine in terms of tartaric acid : A 50.00 mL sample of white wine required 21.48 mL of 0.03776 M NaOH to achieve a phenolphthalein end point. Express the acidity of the wine in terms of tartaric acid (CH2C4H4O6) 150.09 g/mol per 100 mL.
What is the least magnitude of the force : A loaded penguin sled weighing 80.5 N rests on a plane inclined at angle = 18.3° to the horizontal, What is the least magnitude of the force
Specific internal energy of the air increases : Air is initially at a temperature of 500 K and a pressure of 100 kPa. A process occurs so that the specific internal energy of the air increases by 200 kJ/kg (i.e. u2 - u1 = 200 kJ/kg). Modeling the air as an Ideal Gas, determine the final temperatur..
What is the total power dissipated in the circuit : Two resistors are connected in parallel across an ideal 12.0 Volts battery. Resistor A has a value of 28 ohm and resistor B carries a current of 0.2632 A. What is the total power dissipated in the circuit
Normal capacity by using hose connected to kitchen faucet : Due to drought, the water level of a 10-acre pond is five feet below normal. If you wanted to fill the pond to normal capacity by using a hose connected to your kitchen faucet, how long would it take to fill the pond? Select an appropriate unit of ti..
The temperature is 25 degrees c in all cases : A helium tank contains 25.2 leters of helium at 8.4 atm pressure. Determine how many 1.5-L balloons at 755 mm Hg can be inflated with the gas in the tank, assuming that the tank will also have to contain He at 755 mm Hg after the balloons are ..
Estimate what is the induced emf in the loop : If the magnetic field through a loop of N=1000 is perpendicular to the loop, with an area of 5cm2, and increases from B=0 to B=5T in a time of 2sec, What is the induced emf in the loop
Compute the magnetic flux of a square loop : Compute the magnetic flux of a square loop, 2cm on a side, with a magnetic field of 0.400 T. The loop makes a 45 degree angle with the magnetic field
Determine the total number of energy states : Determine the total number (cm3) of energy states in silicon between ev and ev - 4kbt at t=400 Kelvin. ev is the energy at the top of the valence band

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd