Non-reacting gaseous mixture with molar analysis

Assignment Help Mechanical Engineering
Reference no: EM13708478

A non-reacting gaseous mixture with molar analysis of 74.3% N2, 4.3% O2, 7.1% CO2, and 14.3% H2O (g) enters a counter-flow heat exchanger at 800?F and 1 atm with a volumetric flow rate of 5 ft3/s (State 1) and exits at 200?F (State 2). A separate moist air stream enters the heat exchanger at 60F, 1 atm, and relative humidity 30% (State 3) and exits at 100?F (State 4).

a) Show the process for moist air on psychrometric chart. Label states 3 and 4.

b) Calculate the mass flow rate (lbm/s) of moist air.

c) Determine the volumetric flow rate (ft3/s) of moist air at the inlet and at the exit.

Reference no: EM13708478

Questions Cloud

Find the rate of entropy generation in the cooling section : Moist air at 45?C and relative humidity 30% (State 1) with another stream of moist air at 20?C and relative humidity 50% (State 2) in an adiabatic duct. Mass flow rate of dry air is 0.8 kg/s at section 1 and 1 kg/s at section 2. The mixed stream (Sta..
Find at what angle to the vertical is the ray transmitted : A light ray in air is incident on a piece of crown glass (n=1.5) at an angle of 37 degrees from the vertical. At what angle to the vertical is the ray transmitted into the glass
What is the kangaroo average acceleration : A Kangaroo is moving with a velocity of 5.0m/s at an angel of 30 degrees North of East. What is the kangaroo's average acceleration
How long will it take to reach the bottom of hill : A bobsledder starting from rest accelerates uniformly down a 30 degree hill at 3.30m/s2. How long will it take to reach the bottom of the hill if her change in elevation is 110m
Non-reacting gaseous mixture with molar analysis : A non-reacting gaseous mixture with molar analysis of 74.3% N2, 4.3% O2, 7.1% CO2, and 14.3% H2O (g) enters a counter-flow heat exchanger at 800?F and 1 atm with a volumetric flow rate of 5 ft3/s (State 1) and exits at 200?F (State 2). A separate moi..
What is the velocity of the ufo : A UFO is traveling with a velocity of 3250 m/s. Suddenly the retro rocket is fired, What is the velocity of the UFO when the displacement of the craft is 215km, relative to the point where the retro rocket began firing
Compute what are the magnitude and direction : A jet acquires a lift-off speed of 112m/s in 20.0s, starting from rest and traveling due east. What are the magnitude and direction of its average acceleration
Input signal comes from a pressure transducer : Gary is using a 12-bit A/D converter with a range of -10 to 10 V. His input signal comes from a pressure transducer, and has a range of -15 to 15 mV. Gary also has an amplifier circuit (output = G x input, where G is the gain of the amplifier) which ..
How would you describe their difference : What are the different types of non-probability sampling? What are the different types of probability sampling? How would you describe their difference?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd