Neglect effects of gravity and kinetic energy

Assignment Help Mechanical Engineering
Reference no: EM13705965

A rigid container with volume V is originally filled with water of Temperature T1. A hose is then connected to an inlet port and hotter water of temperature T2 is pumped into the container at mass flow rate m in., while another venting port allows the displaced water to flow out , the pressure being constant. Assuming the incoming hot water mixes quickly with the inside water and temperature is a good approximation uniform, derive an expression for the temperature T inside the container as a function of time. Neglect effects of gravity and kinetic energy

Reference no: EM13705965

Questions Cloud

Determine the overall surface efficiency : A 30-cm-long, 1-cm-diameter aluminium fin (k=237 W/m·K) is exposed to an environment at 22oC. The base temperature of the fin is maintained at 80 oC. The heat transfer coefficient between the rod and the surrounding air is 11 W/m2·K.
Consider an ideal simple rankine cycle with steam : Consider an ideal simple rankine cycle with steam as the working fluid. Saturated vapor enters the Turbine at 8 MPa and saturated liquid exits the condenser at a pressure of 0.008 MPa. The net power output of the cycle is 100MW.
Determine the temperature at center plane of the brass plate : A hot brass plate is having its upper surface cooled by impinging jet of air at temperature of 15 [Degree Celsius] and convection heat transfer coefficient of 220 W/(m^2*K). The 10-cm thick brass plate ( p=8530kg.m^3, Cp=380J/(kg*K), k=110 W/(m*K), a..
Heat pump cycle delivers energy by heat transfer to dwelling : A Heat pump cycle delivers energy by heat transfer to a dwelling at a rate of 40,000 Btu/h.The coefficient of performance of the cycle is 2.8. Determine the power input to the cycle, in hp.
Neglect effects of gravity and kinetic energy : A rigid container with volume V is originally filled with water of Temperature T1. A hose is then connected to an inlet port and hotter water of temperature T2 is pumped into the container at mass flow rate m in., while another venting port allows th..
Water is heated until the tank contains only saturated vapor : A closed, rigid tank is filled with water. Initially, the tank holds 9.9 ft^3 saturated vapor and 0.1 ft^3 saturated liquid, each at 212F. The water is heated until the tank contains only saturated vapor.
Forearm acts in geometric center of respective body segment : Assume that the center of masses of the upper arm and the forearm acts in the geometric center of the respective body segment, and the center of mass of the hand acts at the same location that the cable is in the hand (given below). If the person is ..
Determine the eigenvalues and eigenvectors : Determine the eigenvalues and eigenvectors for the following matrices:
What is the overall efficiency of the wind turbine : It is desired to design a wind turbine that will output 2MW of peak electrical power at a location where the average wind speed is 10 m/s and the average ambient conditions are 85 kPa and 5 ?C. What should the rotor blade length be if the aerodynamic..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd