Name two purposes and advantages of jigs

Assignment Help Mechanical Engineering
Reference no: EM131015895

Name two purposes and advantages of jigs and fixtures that are used as work holding devices

 

Reference no: EM131015895

Questions Cloud

What is the acceleration due to gravity : A pendulum of mass 0.4kg and length 0.6 m is pulled back and released from and angle of 10o to the vertical. This same pendulum is taken to another planet where its period is 1.0 second. What is the acceleration due to gravity on this planet?
Define fool proofing in relation to the design of jigs : Define fool proofing in relation to the design of jigs and fixtures as a design consideration to be taken into account
What is the potential energy of the mass : What is the potential energy of the mass at the instant it is released. Choose potential energy to be zero at the bottom of the swing?
Why the original persuasive campaign was unsuccessful : Identify the mistakes made during this failure to communicate. Consider failures in audience research, in understanding audience objections, and in the presentation of the proposed solution.
Name two purposes and advantages of jigs : Name two purposes and advantages of jigs and fixtures that are used as work holding devices
Explain the difference between a jig : Explain the difference between a jig and fixture which are used as work holding devices
Determine net force exerted on q1 by the other two charges : The drawing shows three point charges fixed in place. The charge at the coordinate origin has a value of q1 = +6.09C; the other two have identical magnitudes, but opposite signs: q2 = -4.03C and q3 = +4.03C. Determine the net force exerted on q1 b..
State any two applications of jigs in the engineering : State any two applications of jigs in the engineering laboratory as stated in mechanical engineering
Define the term jig as used in production tools : Define the term jig as used in production tools used to accurately manufacture and duplicate parts in a mechanical engineering laboratory

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Cooling water circulates through a water jacket enclosing a

cooling water circulates through a water jacket enclosing a housing filled with electronic components. at steady state

  Determine the mass flow rate and the rate of heat transfer

R134a flowing at 12 m/s enters a 25 mm diameter tube at a quality of 15%, at 36 Celsius and exits the tube at 10 bars as a saturated liquid. Determine (a) the mass flow rate of the R134a in kg/s, (b) the velocity of the R134a at the exit in m/s and (..

  The charging current must be limited to 20 amps by placing

an automobile battery is modeled as a 12v ideal voltage source in series with a 0.3 ohm internal resistance. it is to

  Find the rate of change of the density in the tire

Air at 250 kPA and 15C is being forced into a tire, which has a volume of 0.5m^3, at a velocity of 60 m/s through a 6 mm opening. Find the rate of change of the density in the tire.

  What will be the static water pressure in pound per square

based solely on available static pressure at a fire hydrant of 51.67 psi that has an elevation of 657 feet above see

  A circular shaft subjected to a repeated axial tensile

a circular shaft subjected to a repeated axial tensile load of 25kn. the shaft is made from aisl 4140 oqt 1100 steel.

  A hollow cylinder made of copper has an outer diameter

A hollow cylinder made of copper has an outer diameter of 200 mm, an inner diameter of 50 mm and a height of 100 mm. Under load P the final height of the cylinder is 60 mm and the inner diameter is 45 mm. If the strength coefficient K is 315 Mpa and ..

  Determine the rate of heat transfer to the rods in the oven

Long cylindrical steel rods (p=7833kg/m3 and cp=0.465kJ/kg*°C) of 8-cm diameter are heat treated by drawing them at a velocity of 4m/min through an 8-m-long oven maintained at 900°C. If the rods enter the oven at 25°C and leave at 750°C,

  Carbon annealed steel rod has a rectangular cross section

The company has been asked to assess the effects of a variety of engineering conditions on a selection of components, perform calculations for the components that follow. A medium carbon annealed steel rod has a rectangular cross section and must cop..

  Determine the equivalence ratio

The components of the exhaust gas of a spark-ignition engine using a fuel mixture represented as C8H17 have  a dry molar analysis of 8.7% CO2, 8.9% CO, 0.3% O2, 3.7% H2, 0.3% CH4, and 78.1% N2. Determine the equivalence ratio.

  In the rectangle in the drawing a charge is to be placed at

in the rectangle in the drawing a charge is to be placed at the empty corner to make the net force on the charge at

  Change in length due to temperature

Calculate the change in length of the steel and aluminium due to the temperature change alone. Then, assuming that the load P is not applied, and the temperature increases from 60?F to 110?F, calculate the change in length of the steel and aluminium.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd