Modern automotive paint plants use water-bornefinishes to

Assignment Help Mechanical Engineering
Reference no: EM13380196

Modern automotive paint plants use water-bornefinishes to minimize the emission of volatile organiccompounds (VOC's) from the plant. In order toproduce a high quality finish, the temperature andrelative humidity in the spray booth must be closelycontrolled. An 'air house' is a small structure thathouses the components necessary to supply, filterand control the temperature and humidity of outsideair, which is then delivered to the spray booth. Forthis problem, design the necessarycomponent layout for an air house, and determinethe energy requirements to operate the air house.

86_What is a typical COP for a commercial chiller.png

The objective of this problem is to design an air house for a Jeep plant in Toledo, OH.

Somedesign constraints are:

  • Summer Outside Air Design Condition: 88 °F (DB), 78 °F (WB)
  • Summer Spray Booth Set-Point: 73 °F (DB), 64 °F (WB)
  • Winter Outside Air Design Condition: 0 °F (DB), φ = 1.0
  • Winter Spray Booth Set-Point: 73 °F (DB), 64 °F (WB)
  • Air Flow Rate (Delivered): 110,000 cfm

You must include/answer at least the following:

1. Design constraints.

2. A schematic layout of the air house, identifying each component (Can be hand drawn. Does not need to be very nice or complex. Just illustrate the idea)

3. A psychrometric chart, illustrating the processes.

4. Condensate and/or Make-up water required, (lbm/hr)

5. Natural gas required, (scfm)

6. An estimate of hourly operating costs, based on energy consumption by component. Uselocal electricity and gas rates. (Note: Natural gas is priced per unit, where 1 unit = 100sft3.)

7. All assumptions, references andall detailed calculations

Estimating Operating Costs for Electricity - Electricity might be used to run the fan to draw air through the system, and also to run a chiller.

Things to consider:

- What is a typical COP for a commercial chiller?

- Typical air house pressure drop is about 4 in. water. How might you estimate fan power requirements?

When using Natural gas, Natural Gas Composition - Natural gas would typically be used to operate any pre-heat or reheat sections, due to the current cost advantage over electricity. For your energy calculations, use the following composition for natural gas:

Natural Gas Composition

Component: Percent by Volume:
CH481.0
C2H6 5.4
C3H8 4.8
C4H10 3.4
N2 5.4

Additional Information

Assume Paint house room dimensions are 100' x 100' x 18' (Length, Width, Height, ft)

Work in US units.

You may neglect things like heat loss/transfer from ducts to surrounding, paint house to surrounds, etc.  Also you may neglect things like heat transfer from people to surrounding, machine to surroundings, or vice versa, etc.

Reference no: EM13380196

Questions Cloud

Write a c program that will calculate the gross pay of a : write a c program that will calculate the gross pay of a set of employees.for each employee the program should prompt
Q1consider the following codedefine add1-iter a-listnbsp : q1consider the following codedefine add1-iter a-listnbsp define add1-helper curr-list result-listnbspnbspnbspnbspnbsp
1 draw a plan of a typical strip mine showing all : 1. draw a plan of a typical strip mine showing all operational features and equipment.2. answer the followinga. why is
Part a a brawl in mickeys backyardread the discussion case : part a a brawl in mickeys backyardread the discussion case a brawl in mickeys backyard question 1 in a chart diagram or
Modern automotive paint plants use water-bornefinishes to : modern automotive paint plants use water-bornefinishes to minimize the emission of volatile organiccompounds vocs from
Build a home security system circuit using this program the : build a home security system circuit using this program. the system must include a door sensorwindow sensor smoke
Relationship to learning outcomescritically analyse the : relationship to learning outcomescritically analyse the theory concepts and models of operations and information
Case study questionspart a 1 how is tesla different to : case study questionspart a 1. how is tesla different to other car manufacturers in terms of concept design and
Reading oakland j s 2003 tqm text with cases case study 4 : reading oakland j. s. 2003 tqm text with cases case study 4 pp. 379-389. 3rd ed. oxford butterworth-heinemann. and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd