Modelling equation for tank height assuming

Assignment Help Chemical Engineering
Reference no: EM13944158

In Number 1 it was assumed that the input and output flow rates could be independently varied. Consider a situation in which the outlet flow rate is a function of the height of liquid in the tank. Write the modelling equation for tank height assuming two different constitutive relationships: (i) F=ßh,or (ii) F=ß , where ß is known as a flow coefficient. You will often see this relationships expressed as F= h/Ror F=,where R is a flow resistance.

List the state variables, parameters, as well as the input and output variables. Give the necessary information to complete the quantitative solution to this problem. If the flow rate has units of liters/min ad the tank has a height of meters, find the units of the flow coefficients and flow resistances for (i) and (ii)

Reference no: EM13944158

Questions Cloud

How plato and aristotle built on pre-socratic philosophy : Based on Aristotle's science of the first philosophy, analyze how Aristotle's metaphysics may guide contemporary people to knowledge about the world. Briefly evaluate how you use either or both of the methods in your own life.
Probability distribution for the number of times : An office manager has several computers running distributed programs. Because of the demands on the system, the machines may crash at various times during the day and require a hard reset. The probability distribution for the number of times a ran..
What is the forecast cash position of jethro : What is the forecast cash position of Jethro Turnbull at the end of the budget year, assuming a current bank overdraft of £15,000?
Means and proportions for several groups : A marketing study conducts 60 significance tests about means and proportions for several groups. Of them, 3 tests are statistically significant at the 0.05 level. The study's final report stresses only the tests with significant results, not menti..
Modelling equation for tank height assuming : In Number 1 it was assumed that the input and output flow rates could be independently varied. Consider a situation in which the outlet flow rate is a function of the height of liquid in the tank. Write the modelling equation for tank height assum..
Algorithm to decide whether there are 2 integers sum equal x : Note that there is no restriction on integers in set P and integer x, that is, we are not restricting ourselves to positive or negative integers.
Social security long enough to be fully insured : Kate is a single parent who earns $40,000 per year. Her household expense are $28,000 per year.  If she were to die, she estimates that the costs of her death would be $10,000.  She has not participated in Social Security long enough to be fully insu..
Compare scholastic, and associationist viewpoints of reality : What are your thoughts on the content of this discussion below. How does this person interpret reality? Do you agree or disagree?
Discuss and define modigliani and miller capital structure : "Discuss and define Modigliani and Miller Capital structure irrelevance theory proposition 1 and 2 and state the difference it makes with tax and without tax "

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Determine blood urea concentration as a function of time

5. A patient is placed on a kidney dialysis unit three times a week. The dialyzer has a membrane area of 1 m2 and is operated in a countercurrent mode. The blood flow rate is 200 ml/min and the dialysate flow rate is 500 ml/min. Membrane permeability..

  Uniform quantizer of the mid-tread type

A sinusoidal signal, with amplitude of 3.25 volts, is applied to a uniform quantizer of the mid-tread type whose output takes on the values 0, ±1, ±2, ±3 volts. Sketch the waveform of the resulting quantizer output for one complete cycle of the in..

  Heat transfer area of the jacket required

HEAT TRANSFER PROBLEM NO 2O- The hot fluid flows through a well mixed stirred tank which is provided with a cooling jacket . the fluid in cooling jacket can also be assumed to be well mixed . what is the heat transfer area of the jacket required?

  Weights on the piston creating pressure down on the gas

Assume you have gas in a cylinder equipped with a piston. There are weights on the piston creating pressure down on the gas.

  What final temperature will be reached by the water

Hydrogen gives off 120. J/g of energy when burned in oxygen, and methane gives off 50. J/g under the same circumstances. If a mixture of 5.0 g of hydrogen and 10. g of methane is burned, and the heat released is transferred to 50.0 g of water at 2..

  How is acetyl chloride produced if 915 gallons is produced

acetyl chloride is a colorless fuming liquid used primarily in the chemical industry.a how is acetyl chloride produced?

  Amount of heat is necessary to synthesize

The enthalpy change of reaction for the balanced equation (with lowest whole-number coefficients) is H  67.7 kJ. If 2.50  102 mL of N2(g) at 100.C and 3.50 atm and 4.50  102 mL of O2(g) at 100.C and 3.50 atm are mixed, what amount of heat is..

  Statistics on the global nanofiltration market outlook

Statistics on the global Nanofiltration market outlook,ie, market trends, size and application. Market drivers and industry structure (market analysis) and likely demand in promising segment such as the water industry or the pharmaceutical ind..

  Significant figures in the naoh molarity

If 2.00 MNaOH is available, how would the student prepare the solution? To help insure three significant figures in the NaOH molarity, to how many significant figures should the volumes and mass be determined?

  Compute the theoretical density of diamond

Compute the theoretical density of diamond given that the C-C distance and bond angle are 0.154 nm and 109.5°, respectively. How does this value compare with the measured density?

  Materials of construction for the shell and tubes

The gases enter the condenser at 230 °C and leave at 50 °C. The cooling water enters the tubes at 20 °C and leaves at 50 °C. Suggest suitable materials of construction for the shell and the tubes.

  Value and direction of a single resultant force

Determine mathematically the value and direction of a single resultant force which when acting upon the plate shown below would effectively replace the forces shown.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd