User Account

All Pages

Modeling a wall-mounted shelf using solidworks

Assignment Help Mechanical Engineering
Reference no: EM132318119

Question:

please make these three parts and put them in an assembly to match the picture below.

Please use solidworks

Assignment : SolidWorks Assemblies

Complete the SolidWorks tutorials or associated materials, as needed, for building parts and assembly SolidWorks.

You have been tasked with modeling a wall-mounted shelf using SolidWorks. The shelf will be mounts using two brackets; two bolts will hold the bracket to the bottom of the shelf. See the two images belc for views of the shelf:

2368_Isometric from top.jpg

View 1: Isometric from top

346_Isometric from bottom.jpg

View 2: Isometric from bottom

Draw each of the three parts using the dimensions on the following page. and combine them into a single ascend*/ The bolts should go through the holes in the top pan of the bracket into each of the four holes you create In the base of the shelf. You do not need to change the material appearance for your solution to make it look like a wood shelf. Also, find the mess properties of the part under the Evaluate tab and selecting Mass Properties.

2352_Bracket Detail.jpg

2303_Shelf Detail.jpg

Reference no: EM132318119

Questions Cloud

Discuss the benefits of executive coaching : Discuss the benefits of Executive coaching. How would you recommend your organization take full advantage of Executive coaching?
Who are major providers of adult and continuing education : Who are the major providers of adult and continuing education in the United States today? Brainstorm a list of different venues where adult learning occurs.
Write report on WHS management system for IT Help Desk : BSBWHS501 - Ensure a Safe Workplace Assignment - Academies Australasia, Sydney, Australia. Write report on WHS management system for IT Help Desk
Justify viable solutions to make your team effective : The course project has major assignments that will be due in Weeks 3 and 5. It will take more than a week's effort to adequately complete them.
Modeling a wall-mounted shelf using solidworks : Modeling a wall-mounted shelf using SolidWorks. The shelf will be mounts using two brackets; two bolts will hold the bracket to the bottom of the shelf
Discuss at least one deadlock prevention : Discuss at least one deadlock prevention, deadlock detection, and deadlock avoidance strategies with an example Operating System that employs these strategies.
Discuss the limitations of a typical case management program : Case management programs are usually considered to be an element of the Quality Assurance Program. However, some health care professionals believe.
Current regulations and customer contracts : It is true that businesses engage in security efforts to protect their assets and comply with current regulations and customer contracts?
Determining the element in the heap : Let x be the last element that was inserted. For each element in the heap, explain why it might be x, or why it cannot be.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the rate of exergy destruction

Consider the parallel flow heat exchanger of Prob. 4.86. Verify that the stream of air exits at 780°R and the stream of carbon dioxide exits at 760°R. Pressure is constant for each stream. For the heat exchanger, determine the rate of exergy destr..

  Distinction between cement and concrete

1 .The mechanical properties of cobalt may be improved by incorporating fine particles of tungsten carbide (WC). Given that the mod- uli of elasticity of these materials are, respectively, 200 GPa (30 x 106  psi) and 700 GPa 2. (a) What is the dis..

  A double acting cylinder with a single rod must produce a

a double acting cylinder with a single rod must produce a thrust of 80kn and move out with a velocity of 3mms on the

  Volume and pressure and the work and heat transfer

Find the final volume and pressure and the work and heat transfer in the process.

  Determine the equivalent stress in the cylinder

Determine the maximum shear stress at the outer surface of the cylinder.

  Tated until its

a rigid 2-ft3 vessel contains water originally at 150of and 5.07 percent quality. the water is then heated until its

  Determine the velocity of the bird

A bird flying at a constant speed at an altitude 100 m is being tracked by a person located directly below the line of flight. If this angle is decreasing at 0.02 rad/s when the angle between the horizon line and the line of site is 45 degrees.

  How much time has elapsed during the four cycles

What is the average coefficient of friction between the two surfaces if the original amplitude was 150 mm? How much time has elapsed during the four cycles?

  Determine the a isentropic efficiency of the compressor b

both heating and cooling for a structure can be furnished by a heat pump. one such device operating in winter uses

  Solve the problem in the image do it step wise in detail

solve the problem in the image. do it step wise in detail. this question is from book fracture mechanics - an

  Determine the mass moment of inertia of the object

Determine the mass moment of inertia about the z axis using composite shapes. Express your answer in terms of the mass m of the object.

  Create the first page using a word processor

Prepare a two-page report on why you selected engineering, what discipline you wish to enter, the possible career paths you might follow, and why. Create the first page using a word processor. Create the second page using a different word processo..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd