Milk enters the tank through a 005 m diameter pipe at a

Assignment Help Mechanical Engineering
Reference no: EM13618867

A large storage tank contains 500,000 L of milk. Milk enters the tank through a 0.05 m diameter pipe at a velocity of 3 m/s. Milk is also being removed at a velocity of 2.5 m/s through a 0.06 m diameter drain. How much milk is in the tank after one hour?

Reference no: EM13618867

Questions Cloud

Assume the refrigerant is a saturated vapor at the : a vapor-compression refrigeration cycle employed in a heat pump uses refrigerant r-134a and provides 15 kw of heating.
Two large parallel metal plates are uniformly and : two large parallel metal plates are uniformly and oppositely charged and the electric field between them is 7.6 times
The pressure at the discharge is 5 psi gage the solution : a 20 degc brix sucrose solution at 70 degf is being pumped from a large open tank at a rate of 16 gallonsmin through a
What is the terminal speed ms at which the bar falls assume : a 55g horizontal metal bar 10cm long is free to slide up and down between two tall vertical metal rods that are 10cm
Milk enters the tank through a 005 m diameter pipe at a : a large storage tank contains 500000 l of milk. milk enters the tank through a 0.05 m diameter pipe at a velocity of 3
A food liquid with a viscosity of 00209 lbf-sft2 is being : a food liquid with a viscosity of 0.0209 lbf-sft2 is being pumped through a two-inch stainless steel pipe at a rate of
A when the spring is released how high does the cheese rise : a piece of cheese with a mass of 1.21 kg is placed on a vertical spring of negligible mass and a force constant k 2200
Also venous blood enters at 0 mm hg and leaves at 15 mm hg : imagine that the heart acts as a pump. blood enters the heart from the lungs at 6mm hg and leaves to the rest of the
A capacitor is charged to a potential of 120 v and is then : a capacitor is charged to a potential of 12.0 v and is then connected to a voltmeter having an internal resistance of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  1 consider the diagram below where a pump is used to draw

1 consider the diagram below where a pump is used to draw water from a lake to feed an irrigation system.a which of the

  Draw a schematic of the system

(a) Draw a schematic of the system and (b) determine if the inventor's claims are true.

  The hull of a boat has a volume of 150 m3 and the total

the hull of a boat has a volume of 150 m3 and the total mass of the boat when empty is 8560 kg. determine how much load

  Initially the container is divided into 2 equal parts using

consider a well insulated container of total volume v.a initially the container is divided into 2 equal parts using a

  Find the momentum and buoyant length scales

find the momentum and buoyant length scales.

  The compressor is cooled by the ambient air at 15 degc at

air enters a compressor at ambient conditions of 100kpa and 17 degc with a low velocity and exits at 1mpa 327 degc and

  During the 50 s interval immediately after braking begins

a motorcycle is moving at 30 ms when the rider applies the brakes giving the motorcycle a constant deceleration. during

  Calculate the modulus of elasticity

Calculate the modulus of elasticity of the aluminium alloy. Use the modulus to determine the length of a 1.25 m bar to which a stress of 210 MPa is applied.

  At steady state the cycle develops 40 kw of power with a

a power cycle operates between a high temperature reservoir at th k and a low temperature reservoir at tc 280 k. at

  A solid shaft l 19 m long is supported between two bearings

a solid shaft l 1.9 m long is supported between two bearings. the shaft rotates at 250 rpm. a 20 degree involute gear

  It is observed that snow lies stably on roofs with a slope

question it is observed that snow lies stably on roofs with a slope of less than 24deg but that it slides off roofs

  Calculate the overall train value

calculate: a) the overall train value. b) the output rational speed at shaft 5. c) the output torque at shaft 5. Relevant gear data is= NA= 17, NB= 36, NC= 19, ND= 41, worm E = double lead, worm G = triple lead, NH= 37?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd