Methane escapes through a small 10-7 m2 hole in a 10-m3

Assignment Help Mechanical Engineering
Reference no: EM13625387

Methane escapes through a small (10^(-7) m^2) hole in a 10-m^3 tank. The methane escapes so slowly that the temperature in the tank remains constant at 23?C. The mass flow rate of the methane through the hole is given by m=0.66 pAv(RT), where p is the pressure in the tank, A is the area of the hole, R is the gas constant, and T is the temperature in the tank. Calculate the time required for the absolute pressure in the tank to decrease from 500 to 400 kPa.

Reference no: EM13625387

Questions Cloud

Neutron stars consist only of neutrons and have : neutron stars consist only of neutrons and have unbelievably high densities. a typical mass and radius for a neutron
A projectile is launched horizontally with an initial : a projectile is launched horizontally with an initial velocity of 25.8 ms and lands on a slope that inclined at 28
The acceleration record shown was obtained during the speed : the acceleration record shown was obtained during the speed trials of a sports car. knowing that the car startys from
Sketch the two processes in series on a t-v diagram : a sealed piston-cylinder assembly contains 3 lbm of water. the water is initially at p1 40 psia and t1 300degf. the
Methane escapes through a small 10-7 m2 hole in a 10-m3 : methane escapes through a small 10-7 m2 hole in a 10-m3 tank. the methane escapes so slowly that the temperature in the
What is the resultant linear acceleration of a point on the : a uniform disk with radius 0.350m and mass 25.5 kg rotates in a horizontal plane on a friction-less vertical axle that
The rod assembly is used to support the 250lb cylinder : the rod assembly is used to support the 250lb cylinder. determine the components of reaction at the ball and socket
If the driver of the automobile traveling north were to : the paths of raindrops during a storm appear to form an angle of 75deg with the vertical and to be directed to the left
Determine the heat transfer coefficient from the gas to the : an experiment is designed to measure the heat transfer from a gas stream at temperature 400 f to the outer surface of a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd