Meteorologist is studying hurricanes and tornadoes

Assignment Help Mechanical Engineering
Reference no: EM13714105

A meteorologist is studying hurricanes and tornadoes. She determines that a particular historic tornado can be described by phi7. At a distance 1 km from the eye of the tornado (the eye is at the origin of the coordinate system) the radial velocity is 1 km/hr (inward towards the origin) and the tangential velocity is 1 km/hr. The pressure 1 km from the eye of the tornado is 14.7 psia. A neutrally buoyant balloon is released 1 km from the center of the tornado. How long will it take to move to a point that is 50 m from the center?

Reference no: EM13714105

Questions Cloud

All rivets are to be of the same size. load on the bracket : The bracket plate is 25 mm thick. All rivets are to be of the same size. Load on the bracket, P = 50 kN ; rivet spacing, C = 100 mm; load arm, e = 400 mm. Permissible shear stress is 65 MPa and crushing stress is 120 MPa. Determine the size of the ri..
Calculate the magnitude and phase by hand : For the following system, G(s) = (s + 50)/ (s + 5) Calculate the magnitude and phase by hand for w = 1, 5, 10, 20, 50, 100 rad/s. Sketch the Bode plot via asymptotes, and compare it to the values from (a).
Determine the amount of energy and the power : Determine the amount of energy (Joules) and the power (Watts) required drilling a hole of 0.2 (5.08 mm) inches in diameter in a Titanium sheet 0.2 (5.08 mm) inches thick.
Consider a friction less fluid with a density : Consider a frictionless fluid with a density of 65 lbm/ft3. We describe this fluid as:
Meteorologist is studying hurricanes and tornadoes : A meteorologist is studying hurricanes and tornadoes. She determines that a particular historic tornado can be described by phi7. At a distance 1 km from the eye of the tornado (the eye is at the origin of the coordinate system) the radial velocity i..
Calculate the temperature of the gas to burn last : An adiabatic constant-volume combustion chamber is filled with a mixture of air and methane; lambda (AFR/AFRs) = 1.3. The initial temperature of the mixture is 25°C, and its pressure is 1 bar.
Heat engine draws equal amounts of energy : A heat engine draws equal amounts of energy from 3 different sources: one at 1000 K, one at 1500 K, and one at 2000 K. The engine rejects heat at a rate of 100 kW to the environment at 300 K. What is the maximum power that the engine can produce?
Fluid property is the kinematic viscosity : An important fluid property is the kinematic viscosity which determines the viscous, or frictional, forces acting in a flow. The kinematic viscosity of air multiplied by 10^6 is given at 350, 450, 500, 550, and 650 K as 20.92,32.39, 38.79, 45.57, and..
Piston cylinder device contains : A piston cylinder device contains 3kg of water vapor at 30 bar and 350ºC. it is cooled at constant volume until the temperature reaches 195ºC. Then it is compressed at constant temperature to 20bar. (a) Show the process on a T-V diagram. (b) Determin..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the tension in the string

If the trap door's weight is 50N. Calculate the tension in the string and the reaction at the hinge.

  Design a basic rankine cycle that uses water

an electrical power plant has stack gases exhausting at 150 degree c. design a basic rankine cycle that uses water

  What time will be required at 500degc to produce the same

the wear resistance of a steel shaft is to be improved by nitrogen hardening of its surface. the initial nitrogen

  Show that the moving cylinder leaves the fixed one when the

a cylinder of radius a is balanced on top of a fixed cylinder of radius b b gt a . if the balance is slightly

  Determine the flight angle that maximizes the flow rate

The die characteristic is Q_x = 0.0015p where p is the head pressure in psi. Determine the flight angle that maximizes the flow rate Q_x and graph it.

  A force of 100 lbf at -30 degrees to the right of the

a mass of 100 slug is towed by 2 ropes one rope pulls with a force of 200 lbf at 30 degrees to the left of the centar

  Calculate the ratio of the exit flow area to the inlet flow

air enters an insulated diffuser operating at steady state with a pressure of 105 nm2 and a temperature of 57 degrees

  Abrasive machining-honing-lapping and surface grinding

Define and identify unique characteristics of the items below: Abrasive Machining, Honing, Lapping, Surface Grinding, Centerless Grinding.

  A baseball is thrown by a pitcher at 95 mph through

a baseball is thrown by a pitcher at 95 mph through standard air. the diameter of the baseball is 2.82in. estimate the

  Determine the mass of vapor present at the initial and final

locate the initial and final states on a sketch of the T-v digram. determine the mass of vapor present at the initial and final state, each in kg.

  Find the global minimum via the golden section search start

1. consider the functionfx 2x4-14x3-60x270xa find the global minimum analytically. evaluate every critical point.b find

  A system executes a power cycle while receiving 1050 kj by

a system executes a power cycle while receiving 1050 kj by heat transfer at a temperature of 525 k and discharging 700

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd