Meteorologist is studying hurricanes and tornadoes

Assignment Help Mechanical Engineering
Reference no: EM13714073

A meteorologist is studying hurricanes and tornadoes. She determines that a particular historic tornado can be described by phi7. At a distance 1 km from the eye of the tornado (the eye is at the origin of the coordinate system) the radial velocity is 1 km/hr (inward towards the origin) and the tangential velocity is 1 km/hr. The pressure 1 km from the eye of the tornado is 14.7 psia. A neutrally buoyant balloon is released 1 km from the center of the tornado. How long will it take to move to a point that is 50 m from the center?

Reference no: EM13714073

Questions Cloud

Refrigeration system-determine the temperature and quality : R-410a flows at 0.3 Ibm/s in a refrigeration system. The R-410a is throttled from 60 F. 270 psia to 45 psia. Determine the temperature and quality of the R-410a after throttling.
Find the maximum length of the specimen before deformation : A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa and an original diameter of 4.0 mm will experience only elastic deformation when a tensile load of 1,500 N is applied. Find the maximum length of the specimen before defo..
Calculate the cross-sectional area of test rod with diameter : A load test on a 8-mm diameter by 375-mm long aluminium alloy rod found that a tension load of 4800N caused an elastic elongation of 0.52-mm in the rod. Using this result, determine the elastic elongation that would be expected for a 23-mm diameter r..
Calculate back pressure to locate shock at the exit plane : Air at a stagnation pressure 700kPa flows isentropic ally through a convergent-divergent nozzle. The design pressure at the nozzle exit is 56 kPa. If the back pressure is raised gradually, thereby creating a shock in the divergent portion of the nozz..
Meteorologist is studying hurricanes and tornadoes : A meteorologist is studying hurricanes and tornadoes. She determines that a particular historic tornado can be described by phi7. At a distance 1 km from the eye of the tornado (the eye is at the origin of the coordinate system) the radial velocity i..
Determine the following for a south facing surface : Determine the following for a south facing surface at 30° slope in Gainesville, FL (Latitude = 29.68°N, Longitude = 82.27°W) on September 21 at noon solar time (Assuming a ground reflectivity of 0.2):
Estimate the radiation reaching the earth! : Please use the radiation fundamental and sun’s size to recalculate the sun radiation power and mass loss rate. Please also estimate the radiation reaching the earth!
The loaded symmetrical truss : Determine the forces in members BC and FG of the loaded symmetrical truss. Show that this calculation can be accomplished by using one section and two equations, each of which contains only one of the two unknowns.
Estimate the radiation reaching the earth : Please use the radiation fundamental and sun’s size to recalculate the sun radiation power and mass loss rate. Please also estimate the radiation reaching the earth!

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd