Membrane made of an isotropic material whose elastic modulus

Assignment Help Mechanical Engineering
Reference no: EM13712623

There is a membrane made of an isotropic material whose elastic modulus and Poisson's ratio is E and v, respectively. When this membrane is elongated along x-direction with no lateral deformation in y-direction, the apparent elastic modulus (E') determined by measured values of stress and strain Sigma_x and Epsilon_x) should be greater than the material's own modulus (E) due to Poisson's effect. Determine the percentage difference between E' and E.

Reference no: EM13712623

Questions Cloud

What are the critical contemporary issues : What are the critical contemporary issues related to consumer buying behavior and perceptions?
The diameter of largest solid sphere for lumped behaviour : For plain carbon steel, with properties at 300K in the Appendix and convection (h=50 W/m^2 K) to air at 500K. the diameter of largest solid sphere for lumped behaviour (2 part- show equivalent length is D/6 and that D for Bi
Performing both an energy balance and an entropy analysis : By performing both an energy balance and an entropy analysis, calculate the change in entropy when 1 mole of saturated ethanol vapor condenses at its normal boiling point.
Assume the entire mass within the house : A heat pump with a COP of 3.0 is used to heat an air-tight house. When running, the heat pump consumes 5 kW of power. If the temperature in the house is 5 degrees C when the heat pump is turned on, how long will it take for the heat pump to raise the..
Membrane made of an isotropic material whose elastic modulus : There is a membrane made of an isotropic material whose elastic modulus and Poisson's ratio is E and v, respectively. When this membrane is elongated along x-direction with no lateral deformation in y-direction, the apparent elastic modulus (E') dete..
Find the indicial equation and its roots : Find the indicial equation and its roots. Find the recurrence relation. Use the recurrence relation to find the first three terms of the power series solution corresponding to one root of the indicial equation
Silicon rubber drain hose for surgical procedure : Silicon rubber has a Poisson’s ratio of 0.4. Consider a silicon rubber drain hose for a surgical procedure; the hose has an outer diameter of 4 mm and a wall thickness of 0.5 mm. How much does the lumen (interior space) of the catheter constrict if t..
Calculate the mole fraction of methane in the fuel : A fuel gas containing methane and ethane is burned with air in furnace, producing a stack gas at 300C and 105kPa (absolute). The stack gas contains C02 at a partial pressure of 80 mm Hg and no CO,O2, methane or ethane. Calculate the mole fraction of ..
Calculate the fluid acceleration : Consider a two dimensional flow X-Y plane (no motion in Z direction). The Velocity field is going by : Y/(X^2+Y^2) and V= -x/(X^2+Y^2). Determine the equation of streamline passing through point X=0 and Y=5. Calculate the fluid acceleration

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd