User Account

All Pages

Maximum temperature in the chip

Assignment Help Mechanical Engineering
Reference no: EM13879960

A simplified representation for cooling in very large-scale integration (VLSI) of microelectronics is shown in the sketch. A silicon chip is mounted in a dielectric substrate, and one surface of the system is convectively cooled, while the remaining surfaces are well insulated from the surroundings. The problem is rendered two- dimensional by assuming the system to be very long in the direction perpendicular to the paper. Under steady-state operation, electric power dissipation in the chip provides for uniform volumetric heating at a rate of q. However, the heating rate is limited by restrictions on the maximum temperature that the chip is allowed to assume.

For the conditions shown on the sketch, will the maximum temperature in the chip exceed 85°C, the maximum allowable operating temperature set by industry standards? A grid spacing of 3 mm is suggested. 

1598_maximum temperature in the chip.jpg

Reference no: EM13879960

Questions Cloud

Assume that you will be giving a presentation : Assume that you will be giving a presentation to the board members on their responsibilities for IT systems. Write a report that could be delivered to the board.
Thermal conductivity of the wet concrete : A small dam, which may be idealized by a large slab 1.2 m thick, is to be completely poured in a short period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3.
Describe these four methods and how they differ : There are four methods of system conversion: parallel, direct cutover, pilot, and phase in. Describe these four methods and how they differ.
Briefly describes the one positive impact and one negative : Provide a paragraph that briefly describes the one positive impact and one negative impact
Maximum temperature in the chip : For the conditions shown on the sketch, will the maximum temperature in the chip exceed 85°C, the maximum allowable operating temperature set by industry standards? A grid spacing of 3 mm is suggested.
Describe the differences between these two feasibility : Two feasibility studies occur during the SDLC: one during systems planning, and one during systems design. Describe the differences between these two feasibility studies.
The democratic and republican parties : Identify one issue area that you want investigate. Use the assigned resources required for this discussion to gather information about the goals and proposals, in that issue area, of three U.S. political parties - the Democratic and Republican par..
Write a paper on movie - the fog of war : Write a two pages describing how these lessons apply to current world events or how these lessons can guide decision making being made by world leaders as current events are unfolding in the world right now.
Why do you think it is particularly challenging : Why do you think it is particularly challenging for companies to maintain ethical behavior during difficult financial times?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd