Maximum inner diameter for the shaft for a yield strength

Assignment Help Mechanical Engineering
Reference no: EM13708242

A shaft with a 2-inch outer diameter must deliver 5000 ft-lbs of torque. The shaft must be hollow and must simultaneously carry hydraulic fluid at an internal pressure of 30,000 psi. Assuming the shaft is closed-ended, and using the von Mises yield criterion with a safety factor of 1.2, specifies the maximum inner diameter for the shaft for a yield strength of (a) 93.6 ksi and (b) 81.6 ksi. State whether the most severe state of stress occurs on the inner or outer surface in each case

Reference no: EM13708242

Questions Cloud

An enclosure contains an array of circuit boards : An enclosure contains an array of circuit boards, 15 cm high and 20 cm long. The clearance between the tips of the components on the PCB and the back surface of the adjacent PCB is 0.3 cm. Each circuit board contains 75 square chips on one side, each..
Determine amount of heat removed during the cooling process : A rigid container of 0.1 m3 and negligible heat capacity contains steam at 500 kPa and 400C. If the container is cooled, determine the pressure and temperature at which steam starts to condense. Determine also the amount of heat removed during the co..
Develop technical competence in problem formulation : Develop your knowledge of key principles relating to wastewater system design - Develop technical competence in problem formulation and solution in this discipline area.
Determine the mass flow rate of air through the compressor : Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 32 °C with a low velocity and exits at 1 MPa and 367 °C with a velocity of 6 x 10^3 m/min. The compressor is cooled at a rate of 1800 kJ/min, and the power input to..
Maximum inner diameter for the shaft for a yield strength : A shaft with a 2-inch outer diameter must deliver 5000 ft-lbs of torque. The shaft must be hollow and must simultaneously carry hydraulic fluid at an internal pressure of 30,000 psi. Assuming the shaft is closed-ended, and using the von Mises yield c..
Business to succeed in today''s business environment : 750 words discussion question. How important is it for sustainable business practices to take hold in order for a business to succeed in today's business environment?
An individual, owns a proprietorship called green : 1. Roger, an individual, owns a proprietorship called Green Thing. For the year 2014, Roger has the following items:-Business income-$200,000.
Determine temperature of air at the exit : At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross sectional areas. The inlet cross sectional area is 6 cm squared. At the duct exit, the pressure of the air is 100 kP..
Assuming constant specific heats for air at room temperature : A well insulated 3-m X 4-m X 6-m room initially at 7 degrees C is heated by the radiator of a steam heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200 degrees C.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd