Maximum fraction of the methane entering the cooler

Assignment Help Mechanical Engineering
Reference no: EM13709117

Dry methane is supplied by a compressor and pre cooling system to the cooler of a Linde liquid methane system. At 180 bar and 300 K. The low–pressure methane leaves the cooler at a temperature 6 C lower than the temperature of the incoming high pressure methane. The separator operates at 1 bar, and the product is saturated liquid at this pressure. What is the maximum fraction of the methane entering the cooler that can be liquefied?

Reference no: EM13709117

Questions Cloud

An ordinary egg can be approximated : An ordinary egg can be approximated as a 5.78 cm diamater sphere. The egg is initially at a temperature of 7.9C and is dropped into boiling water at 97C. Taking the properties of the egg to be p=1020 and cp=3.32. Determine how much heat is transferre..
Calculate the magnitude of the velocity of the rock : A man stands on the roof of a building of height 16.8m and throws a rock with a velocity of magnitude 30.6m/s at an angle of 29.3? above the horizontal. Calculate the magnitude of the velocity of the rock
Determine how far does he slide : A 68-kg base runner begins his slide into second base when he is moving at a speed of 3.9 m/s. How far does he slide
Determine the power delivered by the battery : A 100-m-long copper wire of radius 0.21 mm is connected across a 1.5-V battery. Assume the resistivity of copper is 1.7 x 10-8 Omega•m. Determine the power delivered by the battery
Maximum fraction of the methane entering the cooler : Dry methane is supplied by a compressor and pre cooling system to the cooler of a Linde liquid methane system. At 180 bar and 300 K. The low–pressure methane leaves the cooler at a temperature 6 C lower than the temperature of the incoming high press..
Determine the resistance of one of the bulbs : Nine tree lights are connected in parallel across 120-V potential difference. The cord to the wall socket carries a current of 0.32 A. Determine the resistance of one of the bulbs
Calculate the velocity at the exit of the nossels : The stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically. Air enters a set of these nossels at 270 psia and 795 F with a velocity of 97 ft/s and exists at 200 psia and 550 F. Calculate the..
What was the ray angle of incidence on the crystal : A costume jewelry pendant made of cubic zirconia is submerged in oil. What was the ray's angle of incidence on the crystal
What is the pressure exerted by the gas on the wall : A sealed container has a volume V=0.008 cubic meters and 3 times Avogadro's number of molecules at a temperature T=20 degrees Celsius. What is the pressure P exerted by the gas on the wall of the container

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd