Make reasonable assumptions as to the soil properties

Assignment Help Civil Engineering
Reference no: EM13562500

Soil borings made at a site near Chicago indicate that the top 6m is lose and miscellaneous fill, with the groundwater table at 3m below the ground surface. Below this is a fairly soft blue-gray silty clay with an average water content of 30%. The boring was terminated at 16m below the ground surface when a fairly stiff silty clay was encountered. Make reasonable assumptions as to the soil properties and calculate the total, neutral and effective stresses at 3, 7, 12 and 16m below the ground surface.

Reference no: EM13562500

Questions Cloud

What is the toll that should be charged if it is desired to : A toll bridge carries 5000 vehicles per day when the toll is $1.50/vehicle. It is estimated that when the toll is increased by 25 cents, the traffic on the bridge will decline by 10% of the current volume.
Calculate the force n exerted by the fixed circular slot and : At the instant when theta=35 degrees the orizontal guide is given a constant upward velocity v0=2 m/s. For the instant calculate the force N exerted by the fixed circular slot and the force P exerted by the horizontal slot on the 0.5 kg pin A.
Obtain the change in length of the rod : An aluminum rod is 16.0 cm longat 20°C and has a mass of 350 g. If 13000 J of energy is added to the rod by heat, what is the change in length of the rod
Estimate what is the compressional stress : The total cross-sectional area of the load-bearing calcifiedportion of the two forearm bones (radius and ulna) is approximately2.0 cm2. what is the compressional stress that the arm withstands duringthe crash
Make reasonable assumptions as to the soil properties : Soil borings made at a site near Chicago indicate that the top 6m is lose and miscellaneous fill, with the groundwater table at 3m below the ground surface. Below this is a fairly soft blue-gray silty clay with an average water content of 30%. The bo..
Evaluate what is the mass of the aluminum chunk : A student drops two metallic objects into a 120 g steel container holding 150 g of water at 25°C. What is the mass of the aluminum chunk
Evaluate how much energy is absorbed by the eardrum : A sound wave with an intensity level of 81.0 dB is incident on an eardrum of area0.600 10-4 m2. How much energy is absorbed by the eardrum in 4.0 minutes
Find the minimum coefficient of friction such that : A water jet of diameter 2 inches and speed of v=60 ft/s is filling a tank at a 70 degree angle. The tank has a mass of 25 lbm and contains 6 gallons of water. The water temperature is 70 degrees F.
Calculate the critical crack length required to cause : The specifications on a part specify that the part should be replaced when any crack reaches 25% of the critical crack length that will lead to fracture. We know that the part has an intial crack of length 0.02 mm, and that the fracture toughness is ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  How large must be the tank volume

Neon gas at 50 degrees C in a vertical cylinder of diameter 150 mm has a 6 kg frictionless piston mounted. The outside pressure is 98kPa and the neon volume is 4000cm^3. Find the mass of neon.

  What must the ph be raised to in order to precipitate

Groundwater in Taupe, Arizona, initially contains 1.8 mg/L of iron(III). What must the pH be raised to in order to precipitate 0.3 mg/L of the iron (T=25°C)

  Determine the energy dissipated in the jump

A hydraulic jump forms in a horizontal trapezoidal channel. The base width is 4m and the side slopes are 45o. The depths upstream and downstream of the jump are 1m and 3m.

  Determine the force p required to pull the shaft at velocity

A 25-mm diamenter shaft is pulled through a cylindrical bearing. The lubricant that fills the 0.3-mm gap between the shaft and bearing is an oil having a kinematic velocity of 8.0x10^-4 m^2/s and a specific gravity of 0.91.

  Determine the power input into the heat pump

A heat pump that operates on the ideal vapor compression cycle with refrigerant 134a is used to heat water from 16 to 56 degrees Celsius at a rate of 0.20kg/s. The condensor and evaporator pressures are 1.5 and 0.35 Mpa, respectively. Determine the p..

  Determine the initial weight and final density of the water

A steel tank hold 120 ft^3 of water at atmospheric pressure(14.7psi and 68.4 degrees f). the water is subjected to a 100 fold increase in pressure. determine the initial weight and final density of the water if the volume decreases by .545 ft ^3.

  Calculate the force acting on a window facing the storm

the wind reaches a speed of 27.8 m/s in a storm. calculate the force acting on a 1m x 2m window facing the storm. the window is in a high-rise building. the air density p= 1.2 kg/m3.

  A manufacturer of rat poison in texas proposes to build a

a manufacturer of rat poison in texas proposes to build a circular lagoon to concentrate the arsenic in its rinse water

  What is last year that carbon tetrachloride can be produced

Section 604 of the act lists the phase-out of production of substances that deplete the ozone layer. What is the last year that carbon tetrachloride can be produced

  What will the cars maximum acceleration be on a level road

The car's gear reduction ratio is 3.5 to 1, driveline efficiency is 90%, driveline slippage is 3.5%, and the road-wheel radius is 15 inches. What will the car's maximum acceleration be under these conditions on a level road

  Design settling tank to remove all metal and sand particles

The sand particles range in diameter from 0.04 to 2.0 mm with a specific gravity of 2.65. The wastewater discharge rate is 1400 m3 /d at 20°C. Design a settling tank to remove all the metal and sand particles.

  Determine what constricted width would be to force the flow

Given that uniform flow is subcritcal and there is a constriction in a rectangular channel, how do you determine what the constricted width would be to force the flow to be critical. Draw this transition on a specific energy curve.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd