User Account

All Pages

Make a form tool for lathe for making a convex groove

Assignment Help Mechanical Engineering
Reference no: EM13163863

Make a form tool for lathe for making a convex groove of 3 mm radius. tool material will be tungsten carbide. Know the dimensions of tool.

What is the procedure for deciding values of back rake angles and end clearance angle? will this tool be mounted straight to tool post like thread maki8ng tool?

Reference no: EM13163863

Questions Cloud

Calculate the concentration of a the initial concentration : A certain reaction, a+b=c is the first order with respect to each reactant, with k=1.0x10-2l.mol-1s-1. Calculate the concentration of A remaining after 100s if the initial concentration
What is the mole fraction of hexane : The solution has a vapor pressure of 262 . Pure pentane and hexane have vapor pressures of 425 and 151 , respectively, at room temperature.What is the mole fraction of hexane? (Assume ideal behavior.)
What is the specific heat capacity of this material : A piece of a newly synthesized material of mass 25.0g at 80 degrees C is placed in a calorimeter containing 100g of water at 20 degrees C. If the final temp of the system is 24 degrees C, what is the specific heat capacity of this material?
How many gram sof water were in the sample : a 45-g piece of ice at 0 degrees C is added to a sample of water at 9 degrees C. All of the ice melts and the temperature of the water decreases to 0 degrees C. How many gram sof water were in the sample?
Make a form tool for lathe for making a convex groove : Make a form tool for lathe for making a convex groove of 3 mm radius. tool material will be tungsten carbide. Know the dimensions of tool.
What is the equilibrium partial pressure of h2 : A equilibrium mixture of H2,I2, and HI at 458C contains 0.110 mol of H2, 0.110 mol of I2, and 0.761 mol of HI in a 5.00 L vessel. What is the equilibrium partial pressure of H2 when equilibrium is reestablished following the addition of 0.100 mol ..
State burns in bomb calorimeter in excess oxygen : In another experiment it was determined that for each mole of hydrocarbon, 7 moles of oxygen gas are consumed and 5 moles of CO2 gas and 3 moles of H2O liquid are produced. Find ?H per mole of this hydrocarbon (in kJ) at 298 K
What volume would an equal mass of ethanol occupy : A mass of mercury occupies 0.750 L. What volume would an equal mass of ethanol occupy? The density of mercury is > and the density of ethanol is 0.789 g/mL.
Draw a circuit which implements a 1-to-2 decoder : Q1. Write the truth table for a 1-to-2 decoder. Draw a circuit which implements a 1-to-2 decoder using AND gates, OR gates and NOT gates only.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd