Maintain the heated space at a constant temperature

Assignment Help Mechanical Engineering
Reference no: EM13701706

A heat pump is used to heat a building. The outside air temperature is -10 C and the desired inside temperature is 20.3 C. The heat loss through the walls, ceiling, etc, is 30 kW. Determine the ideal coefficient of performance and the minimum power required to maintain the heated space at a constant temperature.

Reference no: EM13701706

Questions Cloud

Employer transferred her to another town : After her employer transferred her to another town, Rosemary put her house up for sale. After two years of internet listings, open houses, repairs and price cuts, a buy finally came along.
Calculate the rate of heat transfer from this plate : A thin flat plate 6in square with a surface temperature maintained at 250°F is tested for drag in a wind tunnel with an airspeed of 100ft/s. The air is at standard sea level pressure and 60°F and flows over the top and the bottom of the plate. This f..
The velocity at the nozzle exit : Air at 22 kPa, 220K and 250 m/s enters a turbojet engine in flight at an altitude of 10,000m. The diffusor slows the air down to a very low speed relative to its inlet. The pressure ratio across the compressor is 12. The turbine inlet temperature is ..
Electrical energy into mechanical work : If you knew how much voltage you would generate with a given device and you needed to convert that electrical energy into mechanical work, how would you go about doing that?
Maintain the heated space at a constant temperature : A heat pump is used to heat a building. The outside air temperature is -10 C and the desired inside temperature is 20.3 C. The heat loss through the walls, ceiling, etc, is 30 kW. Determine the ideal coefficient of performance and the minimum power r..
Number of watts that must be supplied to the compressor : A Carnot refrigerator using R-134a absorbs heat from a refrigerated space at 0oC and rejects heat to a kitchen at 27oC.The refrigerant enters the evaporator with a quality of zero and exits with a quality of one. The operating pressure of the evapora..
Combustion process taking place in a sealed container : In a combustion process taking place in a sealed container, 160kg of methane is burned in 560kg of O2 and 1845kg of N2 to yield CO, CO2, H2O and N2 as the products of combustion. How many kg of CO are produced?
First law of thermodynamics : Stone Mountain near Atlanta, GA has a sky ride which a gondola is suspended from a cable that takes people to the top of Stone Mountain as well as back down. [MO4, MO5, MO6]. Using the First Law of Thermodynamics, what would be the most efficient way..
Determine the thermodynamic efficiency and back work ratio : A regenerative gas turbine is planned to operate with inlet conditions of 100 kPa and 300 K, a pressure ratio of 6, a turbine inlet temperature of 1600 K, and a net power output of 150 kW. The effectiveness of the regenerator is 90% and the adiabatic..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd