Long rotates about an axis perpendicular

Assignment Help Mechanical Engineering
Reference no: EM13703817

A slender rod 0.6 m long rotates about an axis perpendicular to its length and 0.14 m from its center of gravity. If the rod has a mass of 8 kg, determine its mass moment of inertia about this axis

Reference no: EM13703817

Questions Cloud

Compare the load supporting capability of the three bars : Two round, 3cm diameter bars are made of SAE 1030HR (hot-rolled) steel but are different lengths (15 cm and 60 cm, respectively). Compare the load supporting capability of the three bars if they are loaded in compression and the ends are assumed to b..
What are the typically used thermo set composite resins : What are the typically used thermo set composite resins, and what fiber are they commonly reinforced with?
A car drives on a curved road that goes down a hill : A car drives on a curved road that goes down a hill. The car's position is defined by the position vector, r=(-30.0cos(pi/10.0t)]i+[30.0sin(pi/10.0t)]jâ-(Azt)k} ft where Az=7.00ft/s. The image below shows the system projected onto the x-y plane. What..
Cart travels a track and experiences a constant tangential : A cart travels a track and experiences a constant tangential acceleration from point A to point C. The speeds of the cart are 11.2ft/s at point A and 17.2ft/s at point C. The cart takes 4.50s to go from point A to point C, and the cart takes 1.20s to..
Long rotates about an axis perpendicular : A slender rod 0.6 m long rotates about an axis perpendicular to its length and 0.14 m from its center of gravity. If the rod has a mass of 8 kg, determine its mass moment of inertia about this axis
Lbm block is pushed down a frictionless incline with a force : A 10 lbm block is pushed down a frictionless incline with a force of 5 lbf. the incline is 30 degrees relative to the horizontal. if the block starts from rest, what is its speed after it has been pushed 12 ft. Assume that gravity is 32.0 ft/ sec^2
What is torque required to stop it from spinning : A Cylinder of mass 20 lbs, radius 5in and height 10in is spinning about its axis of symmetry (central axis) at 200 rpms. What is torque required to stop it from spinning
Matrix with digits of the input number as diagonal elements : Write the MATLAB program which takes 8 digits number as input, then creates an 8x8 matrix with digits of the input number as diagonal elements and zeroes elsewhere using for loops. Then, execute the program using your student ID as input.
Determine the actual exit temperature for the compressor : A given mass flow rate (.17 kg/min) of an ideal gas flows through an adiabatic compressor operating at steady state. The compressor has an adiabatic efficiency of N(%) = 87.5. The gas has a molecular weight of MW = 28.5 (kg/kmol) and a specific heat ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd