Location on the cork due to saltwater if the liquid density

Assignment Help Mechanical Engineering
Reference no: EM13706750

A small, narrow, flat-bottomed fishing boat is loaded down with two crew member and a catch fish. The rear of the boat is a plane inclined at an angle theta¸ of 75 degrees with the horizontal. Thirty centimetres below the water surface is a hole in the boat plugged with a corked that is 8 cm in diameter. Determine the force and its location on the cork due to saltwater if the liquid density is 1,025 kg/m3.

Reference no: EM13706750

Questions Cloud

Write a business case memo to the owner : Please assist with the following exercise.  "Your business uses all hubs. Users complain about slow network access. Write a business case memo to the owner justifying the purchase of switches to replace the hubs.
Anti-conservationists decide to get rid of the moon : Anti-conservationists decide to get rid of the moon. Calculate the velocity increment \Deltav required for the moon to escape earth. Lunar lovers want the moon closer to earth. Calculate the minimum total velocity increment to bring the moon closer t..
Calculate the total enthaply change in the first stage : Heating and vaporization using steam tables. A flow rate of 1000 kg/h of water at 21.2C is heated to 110C when the total pressure is 244.2KPA in the first stage of a process. In the second stage at the same pressure the water is heated further, until..
Concentration difference for diffusion across a thin film : If the concentration difference for diffusion across a thin film is doubled, what happens to the flux? If the diffusion coefficient across a thin film is doubled, what happens to the flux?
Location on the cork due to saltwater if the liquid density : A small, narrow, flat-bottomed fishing boat is loaded down with two crew member and a catch fish. The rear of the boat is a plane inclined at an angle theta¸ of 75 degrees with the horizontal. Thirty centimetres below the water surface is a hole in t..
Overview of the evolution of business ethics in america : Overview of Lockheed Martin''s organization and will lay out the research plan that Terris used to obtain information necessary for his work. This will be followed by a general overview of the evolution of business ethics in America.
How to write a program to prepare a marksheet in matlab : How to write a program to prepare a marksheet in MATLAB ?
How power and politics might influence hr processes : Review the Unit Introduction and the Learning Resources - Write a summary in which you critically discuss the potential influences of power and politics that can affect your scenario organisation.
Second-order differential equation : A second-order differential equation x"+9x with initial conditions x(0) = 2 and x'(0) = 0. A first-order differential equation x' + 2x = e^-5t with no initial conditions ( x(0) = x'(0) = 0). Given the differential equation x"+ 6x = f, where f(t) is t..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd