Living plant leaf is an open system that exchanges energy

Assignment Help Mechanical Engineering
Reference no: EM13710263

A living plant leaf is an open system that exchanges energy (sunlight and thermal flows) + matter (O2, CO2, water vapor, etc.) with the surroundings (the exterior). Even with irreversible processes (energy dissipation) we find that the net entropy change for the system + surroundings can decrease; i.e. dS < 0. Using equations presented in lecture and your own critical thinking: a) Explain how this is possible in terms of deS and diS. b) Explain how the Second Law remains valid for this case.

Reference no: EM13710263

Questions Cloud

Find the polynomial by any suitable method : A fourth-order polynomial passes through the five points for which the independent and dependent variables, x and y, respectfully, are given (-2,37), (-1,7), (0,5),(1,13), and (2,61). Find the polynomial by any suitable method. Here, x represents the..
What is the controlling resistance for this heat transfer : A spherical container of outer diameter 2.5 m is buried below the wrath’s surface. The distance of the center of the container to the earth surface is 10 m. The container issued to temporarily store radioactive wastes where heat is generated at a rat..
Determine the rate of heat absorption from the outside air : Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the ra..
Estimate the range flaw sizes : A silicon nitride turbine rotor fractures at a stress level of 265 MPa. Estimate the range flaw sizes that could have been responsible for this failure.
Living plant leaf is an open system that exchanges energy : A living plant leaf is an open system that exchanges energy (sunlight and thermal flows) + matter (O2, CO2, water vapor, etc.) with the surroundings (the exterior). Even with irreversible processes (energy dissipation) we find that the net entropy ch..
Explain why an electric refrigerator : Explain why an electric refrigerator, which transfers energy by means of heat from the cold food storage compartment to the warmer air in the room, is not an impossible "clauses device."
Draw a diagram of the essential features of optical encoder : Explain the principle of operation of an AB encoder and how this is used to read an optical encoder. Draw a diagram of the essential features of an optical encoder.
Determine the velocity of the refrigerant : Refrigerant R22 exits a heat exchanger through a 3 cm diameter tubing with a mass flow of 0.5 kg/s. The temperature and quality are -20 0C and 0.1. Determine the velocity of the refrigerant in m/s.
Measure value and voltage across resistor in dc circuit : We are asked to measure value and voltage across resistor in DC circuit. Explain why - statistical analysis of resistance measurements in different configurations; building series/parallel circuits to compare experimental to theoretical values to ana..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd