Linear model of the transistor

Assignment Help Electrical Engineering
Reference no: EM131228213

Use the two diode model linearized as below

Where β = IC/IB is the current gain, and re is given by the diode equation (m = 1) as 25 mV/ie at room temperature.

222_Figure.jpg

Note: This is a linear model of the transistor. So we are assuming we have biased it at a suitable DC operating point which provides rc, as a known given value. When using a linearized model we are looking for an AC/small signal analysis.

With emitter grounded calculate

a) Input impedance at the base.

b) Output impedance at the collector

c) Output impedance with a resistor R across the constant current source (from the collector terminal to the base terminal)

With base grounded calculate

d) Impedance at the emitter

e) Output impedance at the collector

f) Output impedance at the collector with a resistor R across the constant current source.

With an impedance W to ground at the base

g) Impedance at the emitter

Reference no: EM131228213

Questions Cloud

Determine which variables in your list are stocks : (The Human Body and the U.S. Economy) Based on your own experiences, extend the list of analogies between the human body and the economy as outlined in this chapter. Then, determine which variables in your list are stocks and which are flows.
Raising the funds through retained earnings : If the current tax rate is 40%, how much higher will Turnbull's weighted average cost of capital (WACC) be if it has to raise additional common equity capital by issuing new common stock instead of raising the funds through retained earnings?
Describe the key elements of an information system : Propose a specific electronic health record (EHR) or electronic medical record (EMR) program that is Health Insurance Portability and Accountability Act (HIPAA) compliant. Describe the essential functions, costs, and projected savings for the MCO.
Consider the nmos inverter with depletion load : Determine vI when vO = 1.25 V for the case when (a) the body effect is neglected and (b) the body effect is taken into account.
Linear model of the transistor : Output impedance with a resistor R across the constant current source - This is a linear model of the transistor. So we are assuming we have biased it at a suitable DC operating point which provides.
Define gross domestic product : (National Income Accounting) Define gross domestic product. Determine whether each of the following would be included in the 2004 U.S. gross domestic product
Solve the given question : Determine vO for vI = 0.12 V for the case when (a) the body effect is neglected and (b) the body effect is taken into account.
Identify the level of output per worker produced : Sketch a per-worker production function in the diagram that illustrates the law of diminishing marginal returns. Identify the level of output per worker produced given k capital per worker.
Which nations have experienced the slowest growth : Which nations have experienced the slowest growth? Has productivity actually declined anywhere? How could this be related to the convergence theory explained in this chapter?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the resistance required to reduce the speed

a dc series with an unsaturated field and negligible resistance, when running at a cirtain speed on a given load takes 50A at 460V. If the load -torque variase as the cube of the speed. Calculate the resistance required to reduce the speed 25%.

  What is the binary value on the a-d output pins

An 8-bit A/D converter has Vref- = 2 V and Vref+ = 5 V. The analog input signal vin has a frequency range of 300 Hz to 3.4 kHz. a) If vin = 7 V, what is the binary value on the A/D output pins b) If vin = 1 V, what is the binary value on the A/D outp..

  The condition on the sampling period is determined

Finding the periodicity in N of the discrete time signal x(n) = Cos(3pi*Ts.n + pi/4) and then plotting the discrete signal. From this the condition on the sampling period is determined

  List the three mitigation types

In the presentation, the presenter, Mr. Rob Tucker discussed three types of disturbance mitigation responses or measures. List the three mitigation types and give a short definition of each of the mitigation type.

  Determine the maximum voltage gain

Derive the expression for the voltage transfer function T (s) = Vo(s)/Vi(s). - Determine the maximum voltage gain. -  What is the bandwidth?

  What range of outputs would you expect to actually measure

What closed-loop gain would you expect. If a dc voltage of +1.00 V is applied at the input, what output result. If the 10-k ohm resistors are said to be "1% resistors," having values somewhere in the range (1 ± 0.01) times the nominal value

  Determine the smallest allowable value of resistance

The design guidelines for a circuit call for using only 1/4 W resistors. This means that the resistors are only capable of dissipating .25W of power without sustaining damage. The maximum voltage level in the circuit is known to be 12 V.

  Calculate the unit impulse and the unit step responses

A simple low-pass discrete-time filter is characterized by the following linear difference equation: y[n] = f y[n-1] +(1- f) x[n] , with 0  1 Draw and clearly label an adder-gain-delay diagram for the filter. using the same difference equation from a..

  Find the thickness of the a-plate at the wavelength

If the polarization state resulting from (a) is represented bya complex number on the complex plane, show that the locus of these points as ψ variesfrom 0 to π/2 is a branch of hyperbola. Obtain the equation of the hyperbola.

  What is name given to process of assigning binary number

What is the name given to the process of assigning a specific binary number to an instantaneous value on an analog signal

  How long waveform will take to complete five cycles

If a periodic waveform has a frequency of 20 Hz, how long (in seconds) will it take to complete five cycles?

  Construct a combinational circuit that has a 4-bit bcd digit

The circuit also has a single bit output V. If the 4-bit input is not a valid 8421 BCD digit, V = 0; else V = 1. If V = 0, (the input is not valid) the gray code BCD outputs are don't cares.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd