User Account

All Pages

Let the machine be connected to infinite bus

Assignment Help Electrical Engineering
Reference no: EM131029711

Let the machine be connected to infinite bus, that is, the frequency and magnitude of the terminal voltage of the machine are constant. The dynamic equation is?

 

Reference no: EM131029711

Questions Cloud

Find the slope of the line that goes through (2, 5) (6, 10) : Ship is steaming at 10 knots and picks up ship B on radar 8 miles ahead on the same course. One hour later, ship B is 6 miles ahead. From that point,how long will it take ship A to overtake ship B? What isd the speed of ship B? ( one knot is one m..
A starting torque of 80 nm is developed : A starting torque of 80 Nm is developed in an induction motor by an auto-transformer starter with a tapping of 30%. If the tapping of auto-transformer starter is 60% then the starting torque
Apply equal area criterion neglecting damping andarmature : If Pmax is the maximum power that can be supplied by a cylindrical rotor synchronous machine, state whether the load can be suddenly raised to 0.9 Pmax without destabilising the machine when it is supplying 0.5Pmax .
How long would it take you to complete the task : Include the type of job, the time it takes you and Joe individually to complete the job, and the calculations needed to show how long it would take to complete the job if you worked together. Include units with the answer.
Let the machine be connected to infinite bus : Let the machine be connected to infinite bus, that is, the frequency and magnitude of the terminal voltage of the machine are constant. The dynamic equation is?
A function f with 4 bits of input a3,a2,a1,a0 : Consider a function F with 4 bits of input A3,A2,A1,A0 such that the output of F is 1 if the unsigned binary number represented by A3A2A1A0 is a prime (i.e., 2, 3, 5, 7, 11 or 13). Otherwise, the output of F is 0.
How successful do you think this objection is and why : Finally, assess the strength of the objection you've presented. How successful do you think this objection is, and why
A sequential circuit has two d flip flops a and b : A sequential circuit has two D flip flops A and B, two inputs x and y, and one output z. Behavior of the circuitis described by the following next-state and output equations:A(t+1) = Ay' + xyB(t+1) = B'x' + xy'z = A'(x+y)a. Determine the circuit type..
Find the dimensions of a cylinder of maximum volume : A ball is thrown upward with a velocity of 39.2 m/sec from a height of 6cm. Find

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the magnitude and angle of the current flowing

Given a voltage of 100 volts with a phase angle of 0 degrees, applied across an impedance of 50 ohms at an angle of +30 degrees. This is an inductive impedance - not TOTALLY inductive, but more inductive than capacitive.

  Find the impulse response h of the average

Where x(t) is the input and y(t) is the output. a.] Find the impulse response h(t) of the average. Is the system causal b.] Let x(t) = u(t). Find the output of the average.

  Find the series element for circuit has lagging power factor

find the series element or elements that must be in the enclosed container to satisfy the following conditions. a. average power to circuit = 300W b. circuit has a lagging power factor

  Find the mmf required to get an air gap flux of lines

The core is made of cast steel. Find the MMF required to get an air gap flux of 60,000 lines. The cross sectional area of the center section and air gaps is 4 in^2. The remaining sections have a cross sectional of 6 in^2.

  Why does direction of the net force change over the course

Draw a FBD (free body diagram) for a rocket flying at an arbitrary angle. Indicate the force vector due to gravity and force vector due to air resistance. Why does the direction of the net force change over the course of the rocket's trajectory

  Find a minimal sum-of-products expression for each function

Given a sum-of-products expression, it is possible to write the 1s corresponding to each product term directly on the map without developing an explicit truth table of minterm list, and then proceed with map minimization procedure.

  Determine and represent the signal

Fourier transform X(w)=Xreal(w)+j(Xi(w)). Determine and represent the signal y(w) that gives the fourier transform of Y(w)=Xi(w)+Xreal(w)e^exp(j2w).

  How to three-phase electrical wiring

How To Three-Phase Electrical Wiring installation in a Multi-Story Building ??

  What force f is required by the operator

The floor causes couple moments Ma =60 Nm and Mb =35 Nm on the brushes of the polishing machine. What force F is required by the operator so that the resultantmoment on the polisher is zero. Set a = .3 m.

  Calculate the total power draw by the two loads

Two delta-connvected loads are connected in parallel and powered by a balanced Y-connected system. The small of the two loads draws 10k VA at a lagging Power Factor (PF) of 0.75, and the larger draws 25k VA at a leading PF of 0.80.

  Calculate the short-circuit current in the feeder

Calculate the short-circuit current in the feeder and the voltage of the 400 V busbars when a symmetrical three-phase fault occurs at the far end of the feeder. That fault level of the 11 kV system is 100 MVA.

  What current flows through resistor if resistance is given

the bottom of the conduction band at one end of a silicon resistor is at the same energy level as the top of the valence band at the other end. What current flows through the resistor if the resistance is 1.12k

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd