Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Learning Objectives
- Use modern software tools to analyze a structural system of a building.- Use the standard ASCE 7 Minimum Loads for Buildings and other Structures, to estimate gravity loads, wind forces, and identify design load combinations.- Validate ACI318 code coefficients for estimation of bending moments.
Project Report
• Introduction • Wind Forces on Buildings • Estimation of Gravity and Wind Forces Estimation of dead loads, live loads, and wind forces.• Analysis Results and Discussion o Axial force diagrams, bending moment, diagrams, shear force diagrams, discussion of results and observations.o Analysis of ACI moment coefficients• Conclusions • References
Estimation of External Loads
Gravity Load
Live load: Based on building intended usage. Dead load:• Self-weight• Floor finishes• Mechanical/Electrical/Plumbing• Partitions
Lateral Loads
Seismic Loads: Assume seismic loads are negligible. Wind Forces: Per ASCE 7.
A backsight reading of 2.56 was obtained with rod at A and a foresight reading of 7.45 was obtained with the rod at the trial point B. If B is located 37.00 feet from the center line of a planned 50-foot wide road, is the catch point located uphi..
when the sleeve and the rod are immersed in a pool of oil with dynamic viscosity of 0.095 kg/m.s, the effective weight of the sleeve is 4.5N. how fast will the sleeve slide down the rod
An oedometer test on a clay soil gave the following results: Cc = 0.4, Ce = 0.08, OCR = 5. The thickness of the clay layer in the field is 2.6 m. The existing vertical effective stress at the mid-depth of the clay layer is 150 kPa.
The uniform load has a mass of 450 and is lifted using a uniform 35- strongback beam and four ropes. Determine the Tension in the ropes Determine the force that must be applied at A.
you are designing a highway to AASHTO guidelines on rolling terrain where the design speed will be 65 mi/hr. At one section, a +1.25% grade and a -2.25% grade must be connected with and equal tangent vertical curve.
A fully enclosed cylindrical fuel tank with a diameter of 6.00 meters and a height of 8.00 meters has a manufacturing tolerance of +/- 0.04 meteres for each of these dimensions.
Determine the acceleration when t = 4 s, the displacement from t = 0 to t = 10 s, and the distance the particle travels during this time period.
What is the ratio of the magnitude of E2 to the magnitude of E1? You may neglect the effects of gravity on the proton.
A 45-percent efficient, coal-fired power plant generates output power of 1000 MW (106 kW) and emits SO2 at the legally allowable rate of 0.6 lb SO2 per million BTU of heat into the plant. The stack has an effective height of 250 m.
The car weights 2450 lb, the mechanical efficiency of the drivetrain is 90%, and the wheel radius is 14 inches. The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque.
My question is regarding UVA levels in raw and treated drinking water with regard to TOC and DOC removal. Is there a jar test procedure that incorporates the UVA values of the various stages of treatment and is there a document you could refer me ..
Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd