User Account

All Pages

Knowing that the tank contains compressed air under a

Assignment Help Mechanical Engineering
Reference no: EM13344986

The tank shown has a 180 mm inside diameter and a 12 mm wall thickness. Knowing that the tank contains compressed air under a pressure of 8 MPa, determine the magnitude T of the applied torque for which the maximum normal stress in the tank is 75 MPa.

Reference no: EM13344986

Questions Cloud

A 109-g mixture of nitrogen and carbon dioxide is found to : a 10.9-g mixture of nitrogen and carbon dioxide is found to occupy a volume of 8.88 l when measured at 641.9 mmhg and
Nitrogen dioxide no2 cannot be obtained in a pure form in : nitrogen dioxide no2 cannot be obtained in a pure form in the gas phase because it exists as a mixture of no2 and n2o4.
A buffer ph 370 was prepared by mixing 100 mole of formic : a buffer ph 3.70 was prepared by mixing 1.00 mole of formic acid and 1.00 mole of sodium formate to form an aqueous
Copper has a specific heat of 0092 calgmiddotdegc when 527 : copper has a specific heat of 0.092 calgmiddotdegc. when 52.7 cal of heat is added to a piece of copper the temperature
Knowing that the tank contains compressed air under a : the tank shown has a 180 mm inside diameter and a 12 mm wall thickness. knowing that the tank contains compressed air
Osmium has a density of 226 gcm3 what volume would be : osmium has a density of 22.6 gcm3. what volume would be occupied by a 21.8 g sample of
How much calcium silicate would be formed as a by-product : calcium phosphate silicon dioxide and coke may be heated together in an electric furnace to produce phosphorus as shown
When 0549 moles of a certain gas fill a balloon the volume : when 0.549 moles of a certain gas fill a balloon the volume is 75 ml. if enough of the same gas is added to the balloon
One of the precursors you need to verify a mechanism is : one of the precursors you need to verify a mechanism is benzaldehyde with the para-hydrogen isotopically labelled as

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Sketch the t-s diagram for the cycle

Sketch the T-s diagram for the cycle (put labels and appropriate information)

  What is the diameter of the larger piston

a hydraulic system has a mechanical advantage of 4. If a smaller piston has a diameter of 5 inches what is the diameter of the larger piston?

  A power plant operates a regenerative rankine cycle

A power plant operates a regenerative Rankine cycle with a reheat, one closed and one open feedwater heater and has a net power output of 1.2 x 109 Btu/hr. When the steam exits the boiler it's temperature is 1000°F and its pressure is 1400psi...

  Calculate the kg mix- ture from the mixer

calculate the kg mix- ture from the mixer, kg water evaporated, and kg jam produced.

  Determine the smallest allowable value of the coefficient

determine the smallest allowable value of the coefficient of static friction between the collar and the rod if the collar is not to slide when a) a =15° b)a = 45°. Indicate for each case the direction of the impending motion.

  Calculate the tensile stress required to cause yielding

if the critical resolved shear stress for yielding in aluminum is 240kpa. calculate the tensile stress required to cause yielding when the tensile axis is [001]

  Determine the tensions at the cables

the suspended load exerts a force F=600 lb at A, and the weight of the bar OA is negligible. Determine the tensions at the cables and the reactions at the ball and socket support O

  Determine the required power input to the compressor

Air at the rate of 18 kg/s is drawn into the compressor of a jet engine at 55 kPa and -23oC and is compressed reversibly and adiabatically to 276 kPa. Determine the required power input to the compressor expressed in horsepower.

  Alternative methods for casting the concrete for the wall

Compare the time and cost of using the following three alternative methods for casting the concrete for the wall: 1) direct chute 2) pumped 3) crane and bucket.

  What is the speed of each star at the moment of impact

Gravitational forces pull the two stars together. What is the speed of each star at the moment of impact?

  Calculate the out of balance force

a gear of mass 2.5kg rotates ar 1500rpm.due to an error in manufacture the centre of gravity of the wheel is displaced 0.5mm from the axis of rotation. calculate the out of balance force.

  Determine the size of the equipment

Building HVAC Requirements - Indoor Air Quality and Mechanical Ventilation and how determine the size of the equipment if i need for 60cfm.?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd