Installation of fm radio

Assignment Help Other Engineering
Reference no: EM138970 , Length: 800 Words

Installation of FM radio

At this time working at (xxxplace)  I did budget requisition for equipment needed for radio installation.

I request two 20 feet containerizedstudios, 1 On AIR and two productions Studio, also we request 10 Transmitters planning to cover 10 sites with radio program prepared by our radio staff.

Installation of Radio should be done in two phases; first phase will start when we receive equipment's we are expecting to receive them on June 2014 and we will proceed to install studios in (xxx city) and 5KW transmitter during the Jun-July.

During August up to October we plan to install 3 TVRO transmitters in (regions xxx)

For these three regions we plan to use 2KW EdysstoneFMTransmitters ,for other regions which are going to be installed in second phase we plan to use 1 KW transmitters .

To broadcast in regions we use Satellite to uplink our signal in C band with Dac 7000 audio encoder  and we receive with 2.4 m dish antenna using digital satellite receiver ABR 202A.(to be attached diagram for uplink and down link).

We need to employ 6 studio technicians, to give them training on how to use studios this technicians need to be ready to work on Jun 2014.

For the sites we use 10 ft. Shelter to install our transmitters also we need to request installation of 100 m tall tower where antenna system need to be installed.

For rapid deployment we use pumping mast 13m tall to install one beam antenna until 100m tower is ready.

To install TVRO satellite dish we need 4m2 (square meter)foundation where satellite dish need to be installed .

Reference no: EM138970

Questions Cloud

What will be the electric potential of a point : A 0.12-kg ball is placed in a shallow wedge with an opening angle of 120°, as shown in the figure. For each contact point between the wedge and the ball, determine the force exerted on the ball. Assume the system is frictionless. Find contact force o..
What impulse was impacted by the forces : An 825-N sled is pulled a distance of 161 m. The task requires 1.50 ^ 10^4 J of work and is done by pulling on a rope with a force of 137 N. At what angle is the rope held.
How much would an 80.0 kg person weight on mars : A 220 g air-track glider is attached to a spring. The glider is pushed in 12cm against the spring, and then released. A student with a stopwatch finds that 16 oscillations take 11.5.
What are the direction and magnitude of the elevator : You're driving down the highway late one night at 18 when a deer steps onto the road 36 in front of you. The reaction time before stepping on the brakes is 0.50, and the maximum deceleration of your car is 12.
Installation of fm radio : Installation of FM radio, At this time working at (xxxplace)  I did budget requisition for equipment needed for radio installation.
How much current flows through the television : If the accelerating plates are 1.60 apart, and have a potential difference of 2.60×10^4, what is the magnitude of the uniform electric field between them.
What is the frequency of first overtone : An underwater diver sees the sun 58{rm ^circ} above horizontal. How high is the sun above the horizon to a fisherman in the boat above the diver.
Does the observer at c observe constructive : How long will it take you to cover the 99 m length of the walkway if, once you get on the walkway, you immediately turn around and start walking in the opposite direction with a speed of 1.5 m/s relative to the walkway.
Find out the magnitude of the earth''s magnetic field : A 4.40 kg block is pushed along a floor by a constant applied force that is horizontal and has a magnitude of 40.0 N. it gives the block's speed v versus time t as the block moves along an x axis on the floor. The scale of its vertical axis is set by..

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd