Input range of integral and number of sections

Assignment Help Mechanical Engineering
Reference no: EM13714038

Input range of integral and number of sections

Show results for all of the methods we discussed in lab:

Riemann Low

Riemann High

Trapezoidal

Simpson's 1/3

Create a sub-function for calculating the equation for given x-values like we did in the lab

Create a sub-function for calculating the integral for each method for the equation and range/section.

This will result with one main function for user input and results output and then five sub-functions.

Output results to the screen

Reference no: EM13714038

Questions Cloud

Determine the surface temperature of the heated panel : A room has 1000 ft2 of surface, of which 120 ft2 is to be heated, and the balance has an average surface temperature of 60°F. The air temperature in the room is 68°F. The room is occupied by light clothed adults at rest. Determine the surface tempera..
Associated quantities to be expected on the prototype : The flow around a model of a turbine blade is investigated. The model is five times larger than the prototype. A maximum pressure of 4 psi is measured at the leading edge, a maximum velocity of fps is measured near the top of the blade, and a small d..
What is the maximum gas temperature along the duct : An ideal/calorically perfect gas enters a constant-area heater at a Mach number of 0.20, a total pressure of 700 kPa, and a total temp of 500K. A heat interaction of 1030 kJ/kg into the gas occurs. Determine the Mach number, total pressure (kPa), sta..
What will be the thermal efficiency of the cycle : In a thermodynamic cycle consisting of four processes, the heat and work are as follows: Q (kJ): 30, -10, - 20, 65 W (kJ): 3, 10, - 8, 0. What will be the thermal efficiency of the cycle?
Input range of integral and number of sections : Create a sub-function for calculating the equation for given x-values like we did in the lab. Create a sub-function for calculating the integral for each method for the equation and range/section.
Decorative water fountains consist of water reservoir : Decorative water fountains consist of a water reservoir and underground piping to and from a pump. One such system is shown schematically in the figure. The pipe material is PVC(a table is provided). The outlet line from the pump is 18 m and the inle..
Break-even point : K-Henry's Dull Diner has a contribution margin ratio of 16%. If fixed costs are $176,800, how many dollars of revenue must K-Henry's generate in order to reach the break-even point?
Normalize the following relations to 3nf : Do you always have to use the third normal form? Why or why not? What can happen if you do not use the third normal form? Normalize the following relations to 3NF, using the set of functional dependencies listed:
Both adams and wolfe are large public corporations : Both Adams and Wolfe are large public corporations with subsidiaries throughout the world.   Adams  uses a centralized approach and  makes most of the decisions for its subsidiaries.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd