User Account

All Pages

Incompressible water and inelastic piping

Assignment Help Mechanical Engineering
Reference no: EM13886300

A horizontal water supply pipe has a length of 2000 m and a diameter of 150 mm. The pipe is connected to an open tank at one end where the elevation of water is 4 m, and at the other end there is a quick-opening valve. Determine the time it will take for the ?ow to reach 99% of the ?nal steady-state velocity if the valve is initially closed and then suddenly opened at t ¼ 0. Assume incompressible water and inelastic piping. Let f ¼ 0.030 and K ¼ 0.2 once the valve is opened.

Reference no: EM13886300

Questions Cloud

Determine the mass flux and the downstream pressure : High-velocity air at 20-C and 100 kPa absolute flows in a conduit at 600 m=s. It undergoes a sudden change (a shock wave) to 263 m=s and 438-C with no change in conduit dimensions.
Determine the electron geometry molecular geometry : Determine the electron geometry, molecular geometry, and idealized bond angles for each of the following molecules. CF4
Summarize the key points presented in the article : For this assignment, you are required to read the article entitled "HazMat Emergencies: Decontamination and Victim Chain of Survival," by Gunderson, Helikson, and Heffner (2014), and write a review. The article may be found in the Academic Search Com..
Calculate average velocity of the water leaving the disks : Water flows in a 2-cm-diameter pipe at 10 m=s vertically upward to the center of two horizontal circular disks separated by 8 mm. It flows out between the disks at a radius of 25 cm. Sketch the pipe/disk arrangement. Calculate average velocity of ..
Incompressible water and inelastic piping : Determine the time it will take for the ?ow to reach 99% of the ?nal steady-state velocity if the valve is initially closed and then suddenly opened at t ¼ 0. Assume incompressible water and inelastic piping. Let f ¼ 0.030 and K ¼ 0.2 once the valv..
What realization does chris come at the end? : What realization(s) does Chris come at the end? What do you think lead him to these realization?
Write a picot statement in an area of interest : What type of PICOT question would you create for each of these scenarios and write a PICOT statement in an area of interest to you, which is applicable to your proposed capstone project.
Discuss the hazards posed by the interaction of hazardous : Questions:1. Discuss the hazards posed by the interaction of the hazardous materials present at the refinery and adjacent facilities, including the resulting by-products of the incident fire and acid gas release.
Calculate the flow rate, the mass flux : Air is exiting a 100-cm-diameter balloon out a 1-cm-diameter nozzle. If the pressure and temperature at the exit are 110 kPa and 22-C, respectively, and the exit velocity is 30 m=s, calculate the flow rate, the mass flux, and the rate at which the..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd