In such an experiment for which steady state operation is

Assignment Help Mechanical Engineering
Reference no: EM13628013

The thermal characteristics of a small dormitory refriderator are determined by performing two separate experemints, each with the door closed and the refridgerator placed in ambient air at T (inf)=25 deg C. In one case an electric heater is suspended in the fridge cavity, while the fridge is is unplugged. With the heater dissipating 20 W a steady state temperature of 90 deg C is recorded within the cavity. With the heater removed and now in operation the second experiment involves maintaining a steady state cavity temperature of 5 deg C for a fixed time interval and recording the electrical energy required to operate the fridge. In such an experiment for which steady state operation is maintaned over a 12 hour period, the input electrical energy is 125,000 J. Determine the fridges coefficient of performance COP.

Reference no: EM13628013

Questions Cloud

If the inlet is at the above pressure and saturated vapor : the initial pressure of a steam turbine inlet is determined by adding the last two digits of your student id to 100
Assuming that flow is steady and incompressible obtain a : an incompressible fluid flows past in a solid plate.the x and y coordinates are measured from the leading edge of the
An astronaut is being tested in a centrifuge the centrifuge : an astronaut is being tested in a centrifuge. the centrifuge has a radius of 6.12 m and in starting rotates according
At issue is the proportion of people in a particular county : at issue is the proportion of people in a particular county who do not have health care insurance coverage. a simple
In such an experiment for which steady state operation is : the thermal characteristics of a small dormitory refriderator are determined by performing two separate experemints
A wheel radius 06 m is rolling on a horizontal surface with : a wheel radius 0.6 m is rolling on a horizontal surface with a center of mass acceleration of 0.7 ms2. if the force
Students who have completed a speed reading course have : students who have completed a speed reading course have reading speeds that are normally distributed with a mean of 950
An industrial machine of mass 4534kg is supported on : an industrial machine of mass 453.4kg is supported on springs with a static deflection of 0.508cm. if the machine has a
Calculate the mass flow rate of air and the required power : air is compressed by an adiabatic compressor from 100 kpa and 20 degc to 1.8 mpa and 400 degc. air enters the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd