In state and national forests it is common to store water

Assignment Help Mechanical Engineering
Reference no: EM13626680

In state and national forests it is common to store water in large water towers for reserve in the case of forest fires. To deliver water, the reservoir is connected to a downpipe and then a horizontal cast iron piping system. The downpipe is 80 inches high. The horizontal cast system is 600 inches in length. All the poping is 4 in in diameter. The loss co-efficient for the 90 degree flanged elbow is Kl = 0.3 and the aged cast-iron pipe has a characteristic roughness measured with a micrometer and is equal to 0.51mm.

Use the definition of the loss coefficent and the friction factor for flow in a straight pipe to convert the loss coefficient for the pipe fixture into an equivalent length Leq. Using the moody chart for this flanged elbow the equivalent length of the pipe is 10D. What assumptions have you made using this quantity?

Reference no: EM13626680

Questions Cloud

Find the following a the final volume and the mass of the : one end of a tube is closed and the other is open. a 15 g projectile is placed near the closed end is fastened in place
A high school project involves building a model ultralight : a high school project involves building a model ultralight airplane. some of the stu- dents propose making an airfoil
What must be the new length of the pendulum such that the : a pendulum clock can be approximated as a simple pendulum of length 1.47 m and keeps accurate time at a location where
Find the crank position corresponding to the maximum piston : a find the crank position corresponding to the maximum piston velocity for an in-line slider crank mechanism. crank
In state and national forests it is common to store water : in state and national forests it is common to store water in large water towers for reserve in the case of forest
What is the maximum number of break failures that can be : three coupled street cars are moving at a speed of 32 kmhr down a 7 degree incline. each car has a weight of 198 kn.
The mean errors per page made by a clerk in the word : the mean errors per page made by a clerk in the word processing pool for a large company is thought to be 2.4 with the
A mass-spring system oscillates on a horizontal : 1. a mass-spring system oscillates on a horizontal frictionless surface with an amplitude of 3.94 cm. if the spring
What is the probability that in a group of 10 people from : in a certain population 60 of people have blond hair.a what is the probability that in a group of 10 people from this

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd