In order to measure the volume flow rate of fresh water

Assignment Help Mechanical Engineering
Reference no: EM13627800

Q1.A single stage reciprocating compressor has a swept volume of 0.4 litres and operates at 1440 rpm through a pressure ratio of 8.5 and has a clearance volume of 7% of the swept volume. It is assumed that the gas compression is treated as a polytropic process, with an index of 1.3, and the inlet air conditions of atmospheric pressure, 101 kPa and temperature 25º C. Take Rair = 287 J/kgK.

a). Draw and label the swept, clearance and effective volumes on a P-V diagram and also show the indicated work.

b). Calculate volumetric efficiency.

c). Calculate theoretical mass flow rate.

d). Calculate isothermal efficiency.

e). Calculate power to drive the compressor, assuming ?mech = 81%.

Q2.In order to measure the volume flow rate of fresh water flowing in the pipe of internal diameter of 50 mm, a horizontal venturi tube, of throat diameter of 30 mm, is inserted into a pipe system. When operating; a differential pressure of 18 kPa is measured across the venture meter.

a). Derrive an equation, from first principles, to determine the mean water flow velocity in the pipe.

b). Ignoring any losses, determine, the water volume flow rate.

c). Determine the coefficient of discharge (Cd) for the venture meter if the mass flow rate is measured to be 4 litres/s.

Reference no: EM13627800

Questions Cloud

Suppose you perform a cross between two true-breeding : suppose you perform a cross between two true-breeding stocks of garden peas with respect to two characteristics of
Consider a low speed one-circuit wind tunnel with an inlet : consider a low speed one-circuit wind tunnel with an inlet to throat ratio of 12. the pressure difference between the
The heat flux passing through a plane wall of a : the heat flux passing through a plane wall of a well-insulated house is q 2.5 btuhr-ft2 when the temperature of the
A mass of 040 kg hanging from a spring with a spring : a mass of 0.40 kg hanging from a spring with a spring constant of 80.0 nm is set into an up-and-down simple harmonic
In order to measure the volume flow rate of fresh water : q1.a single stage reciprocating compressor has a swept volume of 0.4 litres and operates at 1440 rpm through a pressure
A 27 cm diameter rod consists of three cylindrical segments : a 2.7 cm diameter rod consists of three cylindrical segments placed end to end in intimate contact aligned aong a
Starting with the energy equation q - w u2 -u1 show that : during a constant pressure process 10 kg of refrigerant 134a at 4degrees c and 10 bars expand to a volume of 0.1 m3.a
When the thinnest string is pressed down at this first fret : the fret closest to the bridge on a guitar is d 21.8 cm from the bridge. when the thinnest string is pressed down at
Starting with the energy equation q - w u2 -u1 show that : during a constant pressure process 10 kg of refrigerant 134a at 4degrees c and 10 bars expand to a volume of 0.1 m3.a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd