Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Implementation of the project:
In this project we are implementing the analog and digital modulation techniques.
Analog: AM,FMDigital: Bpsk,Qpsk
The parameters which are need for the modulation like carrier frequency, angle, and type of mode cane be varied by using the soft core processor called Microblaze.And the message frequency can be varied by using function generator.
In the IEEE paper they mentioned about the analog modulation technique, but we are also doing digital modulation techniques. And we are providing the hardware verification of the project by using CRO, Function Generator, ADC, DAC components.
GivenG(A,B,C) =fm (2,3) + d(4,5,6,7) 1. find the Optimum SOP solution 2. What is the minimum number of gate that can be used to implement this function (d represents dont cares).
A USB communication link requires a circuit that produces the sequence 00000001. You are to design a synchronous sequential circuit that recognizes this sequence. Additionally, there is an E input to this circuit.
Plot the Bode straight-line approximation phase plot (i.e., f(f) vs. f) for the transfer function over the range f = 10 rad/s to f = 100 krad/s using the 4-cycle semi-log graph paper provided. Label all slopes in degrees/dec and all levels in degr..
two resistors with nominal values of 4.7K ohm and 10K ohm, are used in a voltage divider with a +15V supply to create a nominal +10V output. Assuming the resistor values to be exact, what is the actual output voltage produced
The transformer is to be used on a 50 Hz system, with the restriction that it maintain the same maximum core flux and the same total losses. Determine (a) the new voltage rating; (b)the new kVA rating.
What do you notice regarding the gain bandwidth product, power supply requirements, bias current, and input impedance of the LM741 and the LM324 Op Amps
A single phase transformer has the following rating: 120 kVA, 2000 V/100 V, 60 Hz with 1000 primary turns. Determine (A) the maximum flux. (B) given a maximum flux density of 0.25 T, the cross-sectional area of the core.
what effect does the diode barrier potential have on the difference between the peak input voltage and the peak output voltage. Explain
How much we need to pay for the electricity cost in 61 days when a water-desalination machine runs normally from 8AM to 4PM every day. (It draws 25A in its warming-up time (15 minutes) and draws, on average, 7A in its normal working time at 240V).
A series RLC circuit is connected to a 5 V supply, the frequency of the supply is adjusted to give a maximum current of 11.9 mA at 2.5 kHz. The Q factor is 70. Determine the component values of the circuit.
The noise signal is measured to be 1.35 V. The output difference signal is 3.95 V and the common-mode output signal is0.95 mV. Determine the common-mode gain, the differential mode gain, the CMRR, and the CMR (in dB) for the amplifier.
(a) Evaluate the line integral of H about the rectangular path P1(2,3,4) to P2(4,3,4) to P3(4,3,1) to P4(2,3,1) to P1 given H = 3z ax - 2x3 az A/m. (b) Determine the quotient of the closed line integral and the area enclosed by the path as an appro..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd