Implement the function f using only a 3-to-8 decoder

Assignment Help Electrical Engineering
Reference no: EM13263670

Assume we want to implement a function
F(X,Y,Z) = fm(0,1,2,3) + d(4,7) ("d" stands for "do not care").
Label necessary parts of the diagrams with X, X', Y, Y', Z, Z', 1, 0, F, etc...
a) Implement the function F using a minimum number of NAND gates; no additional gates may be used, but you can assume that all variables and their complements are available.
e) Implement the function F using only a 3-to-8 decoder and one additional gate with a minimum number of connections.

Reference no: EM13263670

Questions Cloud

Compute the tensile strain and elongation : In constructing a large mobile, an artist hangs an aluminum sphere of mass 6.0 kg from a vertical steel wire 0.50 m long, compute  the tensile Strain and elongation
Design the complete datapath of the multiplier : Design a multiplier based on the flowing pseudo algorithm where the multiplicand is A and the multiplier is B. P=0 : for i = 0 to n - 1 do if b(i) =1 then P=P+A ; end if; Left-shift A ; end for; a) design the complete datapath (architecture) of the..
How much free cash flow did the firm generate during 2009 : Net income = $825; after-tax operating income [EBIT (1-T)] = $925; EBITDA=1,700; Gross fixed assets = $2,500; and Net operating working capital (NOWC) = 350. Tax rate is 40%. How much free cash flow did the firm generate during 2009?
What is the wacc : If the company's proxy for retained earnings is calculated at 15%, with a 50/50 debt to equity split in capital structure, what is the WACC?
Implement the function f using only a 3-to-8 decoder : a) Implement the function F using a minimum number of NAND gates; no additional gates may be used, but you can assume that all variables and their complements are available. e) Implement the function F using only a 3-to-8 decoder
Show how many u.s. dollars crown co. would receive : what financial tool(s) would be the best available for hedging? Show how many U.S. dollars Crown Co. would receive, net of cost, under each of the tools you have just identified.
How far from the table will the block hit the floor : A block of mass m =2.00kg is released from rest at h=0.300 m from the surface of a table at the top of a theta=50.0 degree incline as shown below. How far from the table will the block hit the floor
What is the expected return on the portfolio : You own a portfolio that is 34 percent invested in Stock X, 24 percent in Stock Y, and 42 percent in Stock Z. The expected returns on these three stocks are 7 percent, 20 percent, and 16 percent, respectively. What is the expected return on the po..
What is the annual coupon rate on this bond : The current price of a 10-year, $1,000 par value bond is $1,000. Interest on this bond is paid every six months, and the simple annual yield is 14 percent. Given these facts, what is the annual coupon rate on this bond?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Create the layout design for mos nand3 gate using depletion

Create the layout design for MOS NAND3 gate using a depletion-type transistor with VTL = -0.3V and enhancement-type transistors with VTO = 0.5V such that VOL is less than or equal to 0.1V. VDD = 2.5V , tox = 10nm and 2X = 0.6μm .

  Define circuit that is needed to use full-scale range of adc

A transducer produces a sinusoidal waveform with an amplitude of 2.5 VPK and a DC offset of 0 VDC. The ADC input signal range is 0 V to 5 V. Describe the signal conditioning circuit that is needed to use the full-scale range of the ADC.

  Compare the one pole rc filters used in an active setup

1 To double the corner frequency in the low-pass and high pass two-pole filters, how would you change the values of the resistors and capacitors .2 Compare the one pole RC filters used in an active setup versus the passive setup

  Determine the quasi-steady-state output voltage

The NMOS transistors in the circuit shown in Figure P16.68 have parameters Kn =0.2mA/V2,VTN =0.5V,λ=0,andγ =0.(a)Forgatevoltagesof φ = 2.5 V, determine the quasi-steady-state output voltage for (i) vI = 0

  Use mips assembly language

Write an assembly program to calculate sum of number10 through 25

  Determine the probability distribution of the number of time

Let us consider the detection of the framing bit in the T1 carrier by the receiver. Assume that the data bits in a frame assume values of 1 and 0 with equal probabilities of 0.5 and independent of each other. The framing bit alternates between 1 a..

  How the voice message is best received

You have a shortwave AM receiver (just an AM receiver that has the capability to receive signals in the FM frequency band) that receives an NBFM voice signal at some carrier frequency. You notice, however, that while the signal strength is maximiz..

  Determine what should the voltage be after some time

One way to measure TC is a square wave generator having a frequency of about 1/10 of the inverse of the time constant. Assuming I apply a voltage of 1 volt across a capacitor of 1uF, and a resistor of 1k

  What is the power level entering the first active stage

What is the power level entering the first active stage of the receiver at 1900 MHz being fed by a 25 meter coax with a loss of 20 dB/km, given that the Isotropic Receive Level is -134 dBW and the receiving station has a 1 meter radius dish

  What heat sink temp is necessary to ensure safe operation

A power transistor for which Tjmax=180degrees Celsius can dissipate 50Watts at a case temperature of 50degrees. If it is connected to a heat sink using an insulating washer for which the thermal resistance is .6degrees Celsius/Watt

  What is average displacement current to nearest microamp

If the capacitor in the previous problem has a plate separation of 1 mm, what is the average displacement current, to the nearest tenth of a microamp, during that time period Assume a resistance of 180006 ohms and an applied voltage of 14 volts.

  What mah capacity should the batteries have

A student project is required to be portable and hand held. It requires 6 V DC power at a current of 150 mA. The batteries for the power supply must last for a minimum of 7 hours of continuous operation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd