Implement a circuit with 3 one bit inputs a-b and c

Assignment Help Electrical Engineering
Reference no: EM13294395

Implement a circuit with 3 one bit inputs A, B, and C and a singleone bit output Z. Z=1 when there are more inputs valued logic one than inputs valued logic zero. Z=0 otherwise. This circuit iscalled a majority one circuit. Show the truth table, the minimal sum of product equation and the logic diagram.

Reference no: EM13294395

Questions Cloud

What countries have the highest rating : How many companies have AAA rating for its bonds? What countries have the highest rating?
Explain specific heat capacity of sand : How much heat is required to warm 1.3kg of sand from 30 degree Celsius to 100 degree Celsius? (According to my notes- specific heat capacity of sand is .84 J/(g x Celsius)
Determine what is upper limit for the device operation : An Si device is doped at 5*10 to the power of 16 cm-3. Assume that the device can operate up to a temperature where the intrinsic carrier density is less than 10% of the total carrier density. What is upper limit for the device operation
Determine the height of the hill : A child and sled with a combined mass of 42.0 kg slide down a frictionless slope. what is the height of the hill
Implement a circuit with 3 one bit inputs a-b and c : Implement a circuit with 3 one bit inputs A, B, and C and a singleone bit output Z. Z=1 when there are more inputs valued logic one than inputs valued logic zero. Z=0 otherwise. This circuit iscalled a majority one circuit.
What is the ships kinetic energy at this time : A large cruise ship of mass 6.80 107 kg has a speed of 12.8 m/s at some instant. what is the ship's kinetic energy at this time
Major developments occurring in the insurance company : Major developments occurring in the insurance company;
What is the charge per unit length lambda on the capacitor : When the capacitor is charged to 135V , what is the charge per unit length lambda on the capacitor
What is the expected value of sample information : What is the expected value of sample information? How much might the physicians be willing to pay for a market study?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How to connect voltage divider to output of dc power supply

Connect a voltage divider to an output of a DC power supply. Design it to give an output that is 1/3 of the supply voltage. Furthermore, neither the power ratings of the resistors nor the current rating of the supply are to be exceeded.

  Calculate the cost of energy for the period 1947 to 1994

Construction on Hoover Dam was started in 1931 and finished in 1935, and the dam was in service from 1936. When completed, it was both the world's largest electric power producing facility and the world's largest concrete structure.

  Determine the sheet resistance and the contact resistance

Measuring the resistances of the resistors with lengths L1 = 10 µm and L2 = 30 µm, the following values are obtained: R1 = 365-ohm and R2 = 1085-ohm, respectively. If the width of the resistors is 5 µm, determine the sheet resistance and the contac..

  Compare the worse case time to do an operation with alu

Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.

  What is the inductance of the load connected in parallel

500W lighting is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7A. What is the inductance of the load connected in parallel with incandesent lights. Assume a voltage of 120v and 60hz.

  Calculate the voltage across the galvanometer and current

A Wheatstone bridge circuit has resistance arms of 400, 40, 602, and 6000 ohms taken sequentially around the bridge. The galvanometer has a resistance of 110 ohms and is connected between the junction of the 40- and 602-ohm resistors

  Determine the length of 10 mm diameter nichrome wire needed

Nichrome wire is used to construct heating elements. Determine the length of 1.0 mm diameter Nichrome wire needed to produce a heating element which has a resistance of 2.0Ω at a temperature of 20 degrees celcius.

  Determine whether number divided evenly can be accomplished

determining whether the number divided evenly can be accomplished by determining if there is a remainder. Implement the program using a for loop for the calculations. Additional hint: a break in the loop can make the program simpler, though it is ..

  What is the number of possible frequency assignments

The MFSK scheme is used in conjunction with an FHSS scheme that hops among 4 different carrier frequencies. What is the number of possible frequency assignments. List the possible frequency assignments.

  Prove the existence of cyclic gray codes for any n

Using VHDL, define a module called "mux 4 to 1" which implements a (4:1) multiplexer. The module should take in 4 data inputs called D3, D2, D1, and D0, and two select inputs called S1 and S0. It should have a single output called Y.

  Sketch bode plot of magnitude of closed loop gain to scale

A certain internally compensated (dominant pole) op amp has a dc gain of 200,000 and 3 dB bandwidth of 5 Hz. Sketch the Bode plot of the magnitude of the open loop gain to scale.

  Determine what is the internal resistance of the source

A short circuit across a current source draws 15 A. If a 10resistor across the source draws 13 A. What is the internal resistance of the source

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd