User Account

All Pages

If this component is subjected to the following state of

Assignment Help Mechanical Engineering
Reference no: EM13638082

An engineering component is made of 7075-T6 aluminum that has 469 MPa in yield strength. If this component is subjected to the following state of stress, determine the safety factor against yielding by the maximum shear stress criterion. s(sigma)x = 100, s(sigma)y = 140, s(sigma)z = -60, txy = 80, tyz = 0, tzx = 0 (MPa).

Reference no: EM13638082

Questions Cloud

The azimuth from station a of a link traverse to an azimuth : the azimuth from station a of a link traverse to an azimuth mark is 212o 12 36. the azimuth from the last station of
Identical point charges of 30e-6c are fixed to 3 of the 4 : identical point charges of 3.0e-6c are fixed to 3 of the 4 corners of a square. what is the magnitude q of the negative
Total extend time for drill feed is 30 seconds with : retrofit an existing clamp and drill circuit for maximum effeiciency. the cylinder that clamps the part into place is a
A charge of -40 nc is at the origin and a second charge of : a charge of -4.0 nc is at the origin and a second charge of 11.0 nc is at x 5.00 m. find the magnitude and direction
If this component is subjected to the following state of : an engineering component is made of 7075-t6 aluminum that has 469 mpa in yield strength. if this component is subjected
A bending moment of 3 kn-m and a torque of 5 kn-m a safety : a solid circular shaft has a diameter of 60 mm and is subjected to a tensile axial load of 200 kn a bending moment of 3
Describe and explain two alternatives to nhst what do their : describe and explain two alternatives to nhst. what do their proponents consider to be their
Independent variable normal birth weight vs low birth : using the information provided indicate which statistical test you think should be used for each of the following
Ball flies 50 yards in this direction before it is caught : in a game of american football a quarterback takes the ball from the line of scrimmage and runs backwards for 10 yards

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a max flowrate of water b the pressure difference

underground water is to be pumped by a 70 percent efficient 3 kw submerged pump to a pool whose free surface is 30 m

  When being chargerd by a 40 volt dc supply find the time t

given that the instantaneous voltage across a capacitor isvc401-e-tcrvoltswhen being chargerd by a 40 volt dc supply

  Calculate the take off thrust assuming that the expansion

in an effort to increase thrust it is decided that an aft-fan should be added to this engine. the aft-fan creates a

  Dislocation densities of 10e7 amp 10e11 cm-2 are typical

dislocation densities of 10e7 amp 10e11 cm-2 are typical for annealed and deformed ni respectively. for each case what

  Determine the total electrical work the heat pump can

a carnot heat pump is to be used for heating house in winter. the house temperature is set at 25oc. one day the outdoor

  At the beginning of the compression process p11bar and

he compressor ratio of an air standard otto cycle is 8. at the beginning of the compression process p11bar and t1300k.

  Air assumed to be a perfect gas flows through a long

air assumed to be a perfect gas flows through a long 2-cm-diameter insulated tube. at section 1 the pessure is 1.1 mpa

  During a certain process 20 kjkg of work is done on the

a closed stationary sytem consists of 2 kg of mass. during a certain process 20 kjkg of work is done on the system and

  Determine the tension in each cable

The rigid L-shaped member ABC is supported by a ball and socket at A and by three cables. Determine the tension in each cable and the reaction at A caused by the 242 kg load applied at G.

  A well-insulated rigid tank contains 5 kg of a saturated

a well-insulated rigid tank contains 5 kg of a saturated liquid-vapour mixture of water at

  Determine the thickness of steel plate required for a 2m

determine the thickness of steel plate required for a 2m diameter cylindrical boiler with hemispherical ends if the

  In state and national forests it is common to store water

in state and national forests it is common to store water in large water towers for reserve in the case of forest

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd