User Account

All Pages

If the water has an initial temperature of 25 degrees

Assignment Help Mechanical Engineering
Reference no: EM13643415

A pot full of water (4L) is to be placed on a stove until it boils. The stove element puts 2500W into the water in the pot and the heat loss from the pot to the atmosphere is 160W. If the water has an initial temperature of 25 degrees celcius, how long in minutes would it take for the pot to boil? Data: Average heat capacity of water = 4.2 kJ/(kg. degrees celcius) , Pot volume is 4L, average water density is 988.1kg/m^3

Reference no: EM13643415

Questions Cloud

The initial concentrations of species are 010 m a 020 m b : for the following equilibrium a 2b lt-gt 3cthe initial concentrations of species are 0.10 m a 0.20 m b and 0.30 m c
Calculate the energy requirement to heat 100 lb water from : calculate the energy requirement to heat 100 lb water from 100 f to 90 c in btu. if an electrical heating element is
The balls have a glancing collision not a head-on collision : one billiard ball is shot east at 2.15 ms. a second identical billiard ball is shot west at 1.42 ms. the balls have a
What minimum mass of succimer in is needed to bind all of : what minimum mass of succimer in is needed to bind all of the lead in a patients bloodstream? assume that patient
If the water has an initial temperature of 25 degrees : a pot full of water 4l is to be placed on a stove until it boils. the stove element puts 2500w into the water in the
The cold reservoir for this plant is a pool of water : imagine that a site in iceland is discovered where temperatures a relatively short distance below the surface of the
The exhaust from a natural gas heating is expelling : the exhaust from a natural gas heating is expelling combustion products at a rate of 10 mole per minute. on a mass
What is the maximum electric power that could be produced : imagine a solar electric power plant that operates by using a gigantic mirror to concentrate light on the boiler for a
The plant generates 20mw of electricity and uses coal with : a power plant has an overall efficiency of 30. the plant generates 20mw of electricity and uses coal with a heating

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The heat transfer in the condenser the boiler and the

consider a steam power plant with reheat that operates on a modified rankine cycle. steam enters the high-pressure

  A circular coil having 19 turns and a radius of r 176cm

a circular coil having 19 turns and a radius of r 17.6cm carries a current of 3.80a. it is placed in a uniform

  A highway patrol officer on the ground uses a radar gun to

1 a highway patrol officer on the ground uses a radar gun to measure the speed of a suspects car to be 60 ms. a patrol

  Increasing the boiler pressure to 600psia while maintaining

a steam power plant is proposed to operate between the pressures of 8psia and 450psia with a max temperature of

  24 lbs of water vapor with an initial volume of 728 ft3 is

2.4 lbs of water vapor with an initial volume of 7.28 ft3 is compressed at a constant pressure of 287lbfin2 to a

  The outer ring rotates and the bearing carries a combined

a 60 mm bore 02 series double row angular contact ball bearing has a 15 degrees contact angle. the outer ring rotates

  Express this compressor work rate in kilowatts and

a heat pump with the elements shown in figure 7.25 condenser to valve to evaporator to compressor to condenser is to be

  A water cooler for drinking water should cool 1 ft3h from

a water cooler for drinking water should cool 1 ft3h from 65 f to 50 f using a small refrigeration unit with at cop of

  If the heating value of the natural gas fuel is 45000 kjkg

a gas turbine power plant produces a net power output of 100 mw with an overall thermal efficency of 35a if the heating

  A steam power plant has a high pressure of 3 mpa and it

a steam power plant has a high pressure of 3 mpa and it maintains 60degc in the condenser. a condensing turbine is used

  Determine the angular velocity theta dot of the combined

a wad of clay mass m1 with an initial horizontal velocity v1 hits and adheres to the massless rigid bar which supports

  Using this form for the diagonal nodes and appropriate

the diagonal of a long triangular bar 45-45-90 triangle section is well insulated. while sides of equivalent length are

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd