If the volumetric flow rate of the air stream is 80 m3min

Assignment Help Mechanical Engineering
Reference no: EM13619044

Atmospheric air at 95 kpa, 30 degrees celcius, and 75% humidity is to be conditioned at constant pressure so that it enters a room at 20 degrees celcius and 40% relative humidity. During the conditioning process, the air entering the conditioning system is first cooled below its dew point by a cooling coil. At the end of the cooling process, the water condenses from the airstream until specific humidity of air reaches its desired value. Once the desired humidity ratio is reached, heat is added to the airstream via heating coils until the desired outlet conditions are achieved. If the volumetric flow rate of the air stream is 80 m^3/,min, calculated the

a) amount of liquid water removed and the total heat and the total heat transfer through the water removal

b) total heat removal rate in the dehumidification section

c) total heat addition rate in the heating section

d) total net heat transfer rate during the entire conditioning process

 

Reference no: EM13619044

Questions Cloud

A pot containing a plant weighing 76 n is hung from the : a pot containing a plant weighing 76 n is hung from the ceiling with a group of bungee cords. if pulled down and
At the beginning of the year you bought a 1000 par value : at the beginning of the year you bought a 1000 par value corporate bond with a 6 percent annual coupon rate and a
Discuss the key motivations leading to the three classes of : problem 1explain the role of the fiber-matrix interface strength in the fracture toughness of fiberreinforced ceramic
The static and kinetic coefficients of friction between the : a wooden crate of mass 25 kg is sitting on a horizontal cement floor. then one end of a horizontal pulley is attached
If the volumetric flow rate of the air stream is 80 m3min : atmospheric air at 95 kpa 30 degrees celcius and 75 humidity is to be conditioned at constant pressure so that it
A man is using a cord to tow a sled at constant speed on a : a man is using a cord to tow a sled at constant speed on a horizontal ground surface. the mass of the sled is 10 kg.
Calculate midlands corporate wacc be prepared to defend : 1. how are mortensens estimates of midlands cost of capital used? how if at all should these anticipated uses
A force has a strength of 87 n and makes an angle of 21 : a force has a strength of 87 n and makes an angle of 21 degrees with respect to the positive x axis in the x-y plane.
Draw a diagram of the system and state necessary : design a stationary steam power plant operating on an ideal closed loop rankine cycle that can deliver 85 mw of net

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd