If the slope of this line is 0675 and the y-intercept is

Assignment Help Mechanical Engineering
Reference no: EM13633419

a) A steel made up of 100% martensite is completely tempered to give an equilibrium composition consisting of 85 wt% ferrite and 15 wt% cementite. What was the carbon content of the austenite prior to quenching if this was a plain carbon steel?

b) Why do alloying additives like Ni, Cr, and Mo help form strong steels?

c) The transformation from austenite to pearlite+ferrite in a plain carbon steel follows Avrami kinetics. A linear relationship is found when ln(ln(1/(1-f)) is plotted on the y-axis and ln(t) is plotted on the x-axis. If the slope of this line is 0.675 and the y-intercept is 5.55, calculate the time in minutes is required for the reaction to reach 50% completion.

Reference no: EM13633419

Questions Cloud

An open-end mercury manometer is connected to a low : an open-end mercury manometer is connected to a low pressurepipeline that supplies a gas to a laboratory. because paint
A pipe at the focal line receives 450 lbmhr of water at 200 : a 300-foot-long 6-ft-wide parabolic trough concentrator receives normal solar radiation at 905 wm2. a pipe at the focal
Find the velocity with which he strikes the water hint when : a diver springs upward with an initial speed of 1.7 ms from a 4.0-m board.a find the velocity with which he strikes the
If an open-tube manometer is open to the atmosphere 760 : if an open-tube manometer is open to the atmosphere 760 torr themercury levels are equal. what is the pressure in the
If the slope of this line is 0675 and the y-intercept is : a a steel made up of 100 martensite is completely tempered to give an equilibrium composition consisting of 85 wt
A hydraulic press consists of two vertical cylinders of : a hydraulic press consists of two vertical cylinders of circular cross-sectional areas 6cm2 and 120cm2 that are joined
Calculate the approximate alkalinity milligrams per : calculate the approximate alkalinity milligrams per litercaco3 for water containing 120 mgl of bicarbonate ionand 15
The facility is required to collect all the vented air and : an alcohol manufacturing facility emits air with 500 ppm ethanol. the air flows out several roof vents at a total flow
A point charge of -15 c is located at the origin a second : a point charge of -1.5 c is located at the origin. a second point charge of 10 c is at x 1 m y 0.5 m. find the x and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd