User Account

All Pages

If the scrap metal density in kgm3 varies with position z

Assignment Help Mechanical Engineering
Reference no: EM13636202

A cylinder of compacted scrap metal measuring 2 m in length and 0.5 in diameter suspended from a spring scale at a location where acceleration of gravity is 9.78m/s^2. If the scrap metal density, in kg/m^3, varies with position z, in m, according to density=7800-360(z/L)^2, determine the reading in the scale, in N.

Reference no: EM13636202

Questions Cloud

Assuming the distribution of study times is normal what : the mean length of time per week that students at a certain school spend on their homework is 24.3 hours with a
Water drips from the nozzle of a shower onto the floor 203 : water drips from the nozzle of a shower onto the floor 203 cm below. the drops fall at regular equal intervals of time
The shelf life of a battery produced by one major company : the shelf life of a battery produced by one major company is known to be normally distributed with a mean life of 3.5
The mass of a string is 90 x 10-3 kg and it is stretched so : the mass of a string is 9.0 x 10-3 kg and it is stretched so that the tension in it is 240 n. a transverse wave
If the scrap metal density in kgm3 varies with position z : a cylinder of compacted scrap metal measuring 2 m in length and 0.5 in diameter suspended from a spring scale at a
In order to get maximum calorific output a burner should : in order to get maximum calorific output a burner should have anoptimum fuel to oxygen ratio which corresponds to 3
Two wires are kept tight between the same pair of supports : two wires are kept tight between the same pair of supports. the tensions in the wires are in the ratio 41 the radii are
Consider the normal freezing point of water what are the : consider the normal freezing point of water. what are the signspositive or negative of deltas and deltah for the
Auto glass companies now have a machine that can repair : auto glass companies now have a machine that can repair broken windshields with a success rate of 85. if a random

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  With u in fts and y in ft a do you think this equation

water flows near a flat surface and soe measurments of the water velocity u parallel to the surface at different

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  A pison-cylinder contains 08 kg of steam of 300oc and 1

a pison-cylinder contains 0.8 kg of steam of 300oc and 1 mpa. the steam is cooled at constant pressure until one-half

  Assume that the change in kinetic energy is negligible

liquid waterh2o at 200 kpa and 20oc is heated in a chmaber by mixing it with a steam h20 at 200 kpa and 150oc. the

  Show the heating-humidification process on a sketch of the

a solar collector is used to dry biomass in a storage bin. outside air at 35o and 60 rh enters the collector and is

  The automatic transmission in a car receives 25 kw shaft

the automatic transmission in a car receives 25 kw shaft work and gives out 24 kw to the drive shaft. the balance is

  A tensile force of 1000 n 225 lbf produces an elastic

consider a cylindrical specimen of some hypothetical metal alloy that has a diameter of 8.0 mm 0.31 in.. a tensile

  Explain carbon content of steel

Carbon content of steel, A steel contains 55% alpha-ferrite and 45% gamma-ferrite or austenite at 750 degrees celcius. What is the carbon content of steel?

  Saturated ammonia vapor leaves an evaporator at 10 f and 05

saturated ammonia vapor leaves an evaporator at 10 f and 0.5 lbms. the velocity must be less than 15 fts. what is the

  Compute the maximum contact pressure and the width of

two mating spur gears are 20 mm wide and the tooth profiles have radii of curvature at the line oif contact of 10 and

  Helium has the lowest normal boiling point of any of the

helium has the lowest normal boiling point of any of the elements at 4.2 k. at this temperature the enthalpy of

  If the columns cross sectional area were uniform the

suppose that you want to design a column to support a uniform compressive stress stress naught. if the columns cross

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd