If the process occurs slowly enough that the temperature in

Assignment Help Mechanical Engineering
Reference no: EM13637014

Atank of 0.1-m3volume contains air at 298.15K (25°C) and 101.33kPa.The tank is connected to a compressed-air line which supplies air at the constant conditions of 318.15K(45°C) and 1500kPa. A valve in the line is cracked so that air flows slowly into the tank until the pressure equals the line pressure. If the process occurs slowly enough that the temperature in the tank remains at 298.15K(25"C), how much heat is lost fromthe tank? Assume air to be an ideal gas for which Cp=(7/2)R and Cv=(5/2)R

Reference no: EM13637014

Questions Cloud

Car 1 is speeding up with an acceleration of magnitude : two cars drive on a straight highway. at time car 1 passes mile marker 0 traveling due east with a speed of 20.0ms .
Determine athe fundamental frequency in hz contained in the : consider the signal yt24sin3pit3cos3pit with t in units of seconds. determine athe fundamental frequency in hz
A solution of h2so4 with unknownconcentration was titrated : a solution of h2so4 with unknownconcentration was titrated with the standard base with .0233molarity. a volume of
What is the recoild speed of the person and the skateboard : a 58-kg person holding two 0.9-kg bricks stands on a 2.6-kg skateboard. initially the skateboard and the person are at
If the process occurs slowly enough that the temperature in : atank of 0.1-m3volume contains air at 298.15k 25degc and 101.33kpa.the tank is connected to a compressed-air line which
How many moles of naoh were required to neutralize the : suppose a standard strong-base solution was prepared byweighing out 1.934g of naoh in 500ml of water. this solution
Calculate the y-component of the force exerted by b on c : particle a of charge 6.00 x 10-4 c is at the origin particle b of charge -7.00 x 10-4 c is at 7.00 m 0 and particle c
Assuming constant specific heats for air at room : a well insulated 4-m x 4-m x 5-m room initially at 10 c is heated by the radiator of a steam heating system. the
An electron has a momentum that is 90 larger than its : an electron has a momentum that is 90 larger than its classical momentum.a find the speed of the electron.b how would

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd