If the point of landing is 20 ft away determine the

Assignment Help Mechanical Engineering
Reference no: EM13623148

During a race the dirt bike was observed to leap up off the small hill at A at an angle of 60o from the horizontal. If the point of landing is 20 ft away, determine the approximate speed at which the bike was traveling just before it left the ground. Neglect the size of the bike.

Reference no: EM13623148

Questions Cloud

Youre trying to save to buy a new 190000 ferrari you have : youre trying to save to buy a new 190000 ferrari. you have 30000 today that can be invested at your bank. the bank pays
The data are presented below is there evidence of a change : fine motor skills were measured in a sample of kindergarteners before and after 6 months of occupational therapy.
Determine the quality of the mixture the mass of liquid and : a 1 m3 rigid vessel contains 1 kg saturated liquid plus vapor h2o at 100oc. determine the specific volume of the
This year ted received a 600 refund of state income tax : this year ted received a 600 refund of state income tax. ted could have deducted 1100 of state income tax on the prior
If the point of landing is 20 ft away determine the : during a race the dirt bike was observed to leap up off the small hill at a at an angle of 60o from the horizontal. if
Light of wavelength 600 nm in air goes into a medium where : light of wavelength 600 nm in air goes into a medium where the index of refraction is 1.73. what is the frequency of
The price of a new car is 16000 assume that an individual : the price of a new car is 16000. assume that an individual makes a down payment of 25 toward the purchase of the car
1 give the null and alternative hypotheses 2 calculate the : a small pilot study is conducted to investigate the effect of a nutritional supplement on total body weight. six
If the ball falls past him 075 s later determine the : a boy throws a ball straight up from the top of a 12m tower. if the ball falls past him 0.75 s later determine the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  During a certain process 20 kjkg of work is done on the

a closed stationary sytem consists of 2 kg of mass. during a certain process 20 kjkg of work is done on the system and

  A r-12 plant is to develop 5 tons of refrigeration the

a r-12 plant is to develop 5 tons of refrigeration. the condenser and evaporator temperature are to be 40c and -10 c

  Determine the maximum input frequency for a vibration such

a seismic instrument has a natural frequency of 20 hz and a damping ratio of 0.65. determine the maximum input

  Determine the thermal efficiency and the required steam

determine the thermal efficiency and the required steam flow rate kgs for a reheat-regenerative steam power plant which

  Calculate the isentropic work process 1-2s the actual work

air at mass flow rate of 10 kgs at 1 atm 300 k point1 enters an adiabatic compressor and exists at 8 atm 600 k point 2.

  Determine a the minimum diameter of the inlet pipe in cm so

ammonia enters a control volume operating at steady state at p1 14 bar t1 28 oc with a mass flow rate of 0.5 kgs.

  Estimate the land area required to grow willow that would

estimate the land area required to grow willow that would provide 1 gw of power in a region where the annual solar

  At what temperature does the first liquid phase form

What is the composition of the last solid remaining prior to complete melting?

  A pressure gauge measures a pressure downstream from the

water is flowing through a gradual constriction in a pipe. the upstream diameter of the pipe is d14cm and the

  Determine the phase or phases in a system

Determine the phase or phases in a system consisting of H2O at the following conditions and sketch p-v and T-v diagrams shown the locations of each state?

  Find the speed of the block

Assuming the pulley is a uniform disk with a mass of 0.31 {rm kg}, find the speed of the block after it has fallen through a height of 0.50 {rm m}.

  What is the force needed to seperate the top surface

A layer of water seperates two smooth surfaces a distance of 2r. Derive an experssion for the force needed to pul the two surfaces apart. Consider the bottom surface fixed. What is the force needed to seperate the top surface?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd