User Account

All Pages

If the mean thickness is 3mm and the standard deviation is

Assignment Help Mechanical Engineering
Reference no: EM13609640

The thickness of a set of gaskets varies because of random manufacturing disturbances but the thickness values measured belong to a Gaussian distribution. If the mean thickness is 3mm and the standard deviation is 0.25, calculate the percentage of gaskets that have a thickness greater than 2.5mm.

Reference no: EM13609640

Questions Cloud

Then in another 4 s it moves from sb to sc 25m determine : a particle travels along a straight line such that in 2 s it moves from an initial position sa 0.5m to a position sb
The following information is collected from students upon : the following information is collected from students upon exiting the campus bookstore during the first week of
A level perpetuity-immediate is to be shared by three : a level perpetuity-immediate is to be shared by three charities providing medical research and a fourth charity
Two charged spheres are 527cm apart they are moved and the : two charged spheres are 5.27cm apart. they are moved and the force on each of them is found to have been tripled how
If the mean thickness is 3mm and the standard deviation is : the thickness of a set of gaskets varies because of random manufacturing disturbances but the thickness values measured
The author recorded actual temperatures along with : the author recorded actual temperatures along with temperatures that were predicted 5 days earlier. results are listed
Snipe company has been purchasing a component part q for : snipe company has been purchasing a component part q for 19.20 a unit. snipe is currently operating at 70 of capacity
Use a 05 significance level to test the claimignificance : use a .05 significance level to test the claimignificance level to test the claim that paired sample data below come
Saturated vapor at 150 kpa it is heated to 40 c and the : a pistoncylinder .5 kg steel altogether maintaining a constant pressure has .2 kg r134a as saturated vapor at 150 kpa.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Dtermine the maximum stress and the direction of the

a shaft is subjected to bending and torsion such that the bending stress on the surface is 80 mpa and the shear stress

  Using the formula to compute torque and having a torque

Using the formula to compute torque and having a torque of 4966.97, with the RPM's at 250, Would my calculation for horsepower be correct at 236.4 hp?

  The inner and outer surfaces of a 6-m x 7-m brick wall of

the inner and outer surfaces of a 6-m x 7-m brick wall of thickness 41 cm and thermal conductivity .69 wmc are

  Calcualte the efficiency of centrifugal compressor

I would expect somthing like the requirement to execute the equation, please explain each term in the equation with its engineering units.

  What is the natural coefficient of variation

Now suppose the mean time to failure (mf) on the expose machine is 60 hours and the repair time is exponentially distributed with a mean of 2 hours (mr). What are the effective mean and CV of the process time for a job of 60 panels?

  A 250-kg crate b is suspended from a cable attached to a

a 250-kg crate b is suspended from a cable attached to a 20-kg trolley a which rides on an inclined i-beam as shown.

  Determine the pressure on the bottom surface of the fluid

a 6.5m tall tank has a rectangular cross?section and is filled with water to a depth of 3.5m. assuming the pressure on

  An engine block with a surface area measured to be 090m2

an engine block with a surface area measured to be 0.90m2 generates a power output of 55 kw with a net engine

  Determine the velocity va

The catapult is used to launch a ball such that it strikes the wall of the building at the maximum height of its trajectory. If it takes 1.5 s to travel from A to B, determine the velocity vA at which it was launched, the angle of release q, and t..

  The temperature profile as a function of radial position

(a) The temperature profile as a function of radial position

  Calculate the mach number of flight in both cases

An airplane flies at 400 mph at 1600 ft altitude on a standard day. The plane climbs to 50,000 ft and flies at 725 mph. Calculate the Mach number of flight in both cases.

  How many engagement points on flywheel would be necessary

A full revolution press has 100 rpm flywheel rotation. The press is equipped with tow hand trip devices mounted on the machine at a distance of 20 inches from the point of operation. How many engagement points on the flywheel would be necessary to ma..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd